Vermont Castings VC31CDVINTSC Скачать руководство пользователя страница 17

Страница: 17 / 48

20304166

VC31LDVI/VC31CDVI Gas Fireplace Insert

INstAllAtION

CheCK GAs type

Use proper gas type for the insert you are installing. If you

have conflicting gas type, do not install insert. See dealer

where you purchased the insert for proper insert according

to your gas type.

INstAll GAs pIpING tO INseRt lOCAtION

INstAllAtION Items NeeDeD

Make sure you have the items listed below before install-

ing appliance.

•

Piping (check local codes)

•

Test gauge connection*

•

Tee joint

•

Pipe wrench

•

Sealant (resistant to propane/LP gas)

•

Sediment trap (optional but recommended)

•

External regulator (supplied by installer)

•

approved flexible gas line with gas connector (if allowed

by local codes — not provided)

* A CSA design-certified equipment shutoff valve with

1/8" NPT tap is an acceptable alternative to test gauge

connection. Purchase the CSA design-certified equip-

ment shutoff valve from your dealer.

For propane/LP connections only, the installer must supply

an external regulator. The external regulator will reduce

incoming gas pressure. You must reduce incoming gas

pressure to between 11 and 13 inches of water. If you do

not reduce incoming gas pressure, burner system regula-

tor damage could occur. Install external regulator with the

vent pointing down as shown in

Figure 18

. Pointing the

vent down protects it from freezing rain or sleet.

FP1930
external regulator
9/08

External

Regual-

tor

Vent

Pointing

Down

100 gal. (min.

Propane/LP

Supply Tank

FP1930

Figure 18 -

External Regulator with Vent Pointing Down

(Propane/LP Only)

A qualified installer or service person must

connect appliance to gas supply. Follow all

local codes.

ARNING

For propane/lp units, never connect insert

directly to the propane/lp supply. this burn-

er system requires an external regulator

(not supplied). Install the external regulator

between the burner system and propane/lp

supply.

ION

use only new black iron or steel pipe. Inter-

nally tinned copper or copper tubing can be

used per National Fuel Gas Code, section

2.6.3, providing gas meets hydrogen sulfide

limits, and where permitted by local codes.

Gas piping system must be sized to provide

minimum inlet pressure (listed on data plate)

at the maximum flow rate (Btu/hr). undue

pressure loss will occur if the pipe is too

small.

ION

Содержание VC31CDVINTSC

















































Результаты поиска

Содержание VC31CDVINTSC

Отзывы:

Похожие инструкции для VC31CDVINTSC

Бренды по названию

Популярные бренды

Vermont Castings VC31CDVINTSC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VC31CDVINTSC

Отзывы:

Похожие инструкции для VC31CDVINTSC

Бренды по названию

Популярные бренды