manualshive.com logo in svg

Vermont Castings TrimWorks DVA4136, Инструкции по установке и руководство для владельца, Страница: 27 / 44

Поделиться
Скачать
Vermont Castings TrimWorks DVA4136 Скачать руководство пользователя страница 27

27

DVA4136 Series Direct Vent Gas Fireplace

10010270

Remote Control Transmitter Operation Matrix

Set Temperature:

  This will ONLY appear when the  

 

THERMOSTAT is activated

Manual ON:

 

When manual ON, the word ON  

 

will appear and when manual OFF  

 

the word OFF will appear.

Program Mode:

 

This P1 and P2 for weekdays  

 

and weekends icon will appear  

 

when the program is operational 

Thermostat Range:

 

The range for the room   

 

temperature readout is 32-99° F.   

 

The room temperature always  

 

displays on the LCD. 

 

The range for set temperature is  

 

45- 99° F.  It is factory set at 45°F.  

 

The users will have to use UP/ 

 

DOWN buttons to set their desired  

 

set temperature.

Flame Icon:

 

The flame-1 icon will be ON all the  

 

time the main or the rear burner  

 

flame is ON, whether it is under  

 

Manual ON, THERMOSTAT or  

 

PROGRAM modes.

The installation of the transmitter batteries, 2 "AAA", will 
activate the initial set up of the system. Setup mode can 
also be activated at any time by pressing the FLAME 
REAR and PROG/TIME buttons simultaneously for 5 
seconds. The control will automatically exit setup mode 
if no button is pressed within 20 seconds.
This system will allow the temperature unit conversion, 
gas type conversion, and clock set up while in Setup 
mode per the following setup procedure.

Setting of C/F conversion:

 

•  C/F conversion: Use UP or DOWN key to choose 

Celsius or Fahrenheit, Press "SET" button to 
continue to gas type setup.

Gas Type Conversion:

 

•  NG/LP conversion: Use UP or DOWN key to choose 

Natural Gas or Liquid Propane, Press "SET" button 
to continue to clock set up.

Clock Setup: 

•  Use UP or DOWN key to set "Hour", then press SET 

to enter “Minute” setting.

•  Use UP or DOWN key to set “Minute”, and then 

press SET to enter "AM/PM" setting.

•  Use UP or DOWN key to set "AM/PM", the press 

SET to enter "Day of Week" setting.

•  Use UP of DOWN key to select the "Day of the 

Week".

Manual Mode

Push MODE button for manual ON, the flame ICON 
will come on the LCD screen. The second push of the 
MODE button will put the control into the THERMO 
mode. You can continue to push the MODE one more 
time to OFF.

NOTE:  The MODE button will operate ON - 
THERMO - OFF in a series that will cycle from ON to 
THERMO to OFF.
Fan Mode

The control of the fan will be from a button on the 
handheld transmitter.  When the FAN button is pressed, 
the FAN setting level will flash on the LCD display and 
the user can select desired setting from highest to 
lowest with 6 different levels to the fan motor via the UP 
and DOWN buttons.  If no adjustment is made within 7 
seconds, the control will exit the function setting mode 
and the LCD display will return to the normal view.
Delayed ON/OFF – The fan output will be energized 5 
minutes after the main flame is turned on and will be 
turned off 12 after the main flame is turned off.  This 
applies to both manual and thermal mode.  If the main 
flame is turned off and then cycled back on within the 
12 minute off-delay period, the fan should remain on 
(the 5-minute ON delay is omitted in this condition).

Lighting Mode

The control of the lighting output will be from a button 
on the handheld transmitter.  When the LIGHT button is 
pressed, the LIGHT setting level will flash on the LCD 
display and the user can select desired setting from 
highest to lowest with 6 different levels to the lighting 
output via the UP and DOWN buttons.  If no adjustment 
is made within 7 seconds, the control will exit the 
function setting mode and the LCD display will return to 
the normal view.
The lights are completely independent of the main 
flame coming ON and OFF.  The user can turn the 
lighting output ON or OFF regardless of the state of the 
main flame and changing the state of the main flame 
will have no effect on the lighting output.

Continuous Pilot

Operation of this feature of having the pilot to run all the 
time will be activated with the pressing of two buttons, 
"PROG/TIME" & "FLAME 1". This action will activate 
the Icon on the LCD screen. Pressing of the same two 
buttons will de-activate the feature.
This feature is the same as the standard AF-4000 
module, but activation of the system is different in that 
two buttons must be depressed to activate or de-
activate the function.  This feature can also be activated 
via a 2-position switch on the side of the main module.

Содержание TrimWorks DVA4136













































Отзывы:

Нет отзывов