Vermont Castings TrimWorks DVA4136 Скачать руководство пользователя страница 33

Страница: 33 / 44

DVA4136 Series Direct Vent Gas Fireplace

10010270

Conversions must be completed by qualiﬁed personnel

Fuel Conversion Instructions

To convert the DVA4136 units for use with a different
gas follow these instructions. Before proceeding, turn
control knob on valve to

“OFF”

and turn gas supply

OFF

. Turn

OFF

any electricity that may be going to the

appliance.

CAUTION: Logs may be HOT! Allow to cool before
proceeding.

1. Open louvre assembly bottom or bottom access

panel to gain access to valve. Remove window
frame assembly. (See “Window Frame Assembly
Removal”, Page 21, Fig. 36)

2. Remove logs if previously installed.

American Flame Valve

1. Remove rubber cap from valve. (Fig. 49)
2. Push pin in and turn so line on the end of the pin

aligns with the appropriate gas. NAT for natural gas
and LP for propane.

3. Replace cap.
4. Remove minimum rate screw and replace with new

minimum rate screw supplied in kit. Refer to Table 1
on Page 34.

Valve conversion is complete.

housing assembly holding the shutter spring and
mixer tube assembly. Carefully remove the mixer
tube assembly from the burner housing assembly.

2. Remove and discard the shutter spring assembly.
3. Remove the air shutter from the mixer tube by re-

moving one screw.

4. Install this air shutter to new mixer tube supplied

with conversion kit using screw from old mixer tube.

5. Install new mixer tube into burner housing assembly

taking care to properly align gasket with mixer tube
mounting plate.

6. Reassemble into the ﬁreplace the burner housing

assembly, the burner tube assembly and the fettle in
reverse order.

Mixer Tube Replacement

(Conversion to NG ONLY)

1. Remove the 2 screws from the left end of the burner

housing assembly holding the mixer tube assembly.
Carefully remove the mixer tube assembly from the
burner housing assembly.

2. Remove the air shutter from the mixer tube by re-

moving one screw.

Inlet

PILOT

Pilot Adj.

Outlet

MAIN

FP1769
AF4000 valve face
2/07

��
��
��

�

��

�

��

Main Connection

Rubber Cap

Gas Type
Marker

FP1769a

CO137

Minimum
Rate Screw

Fig. 49

Remove rubber cap and adjust gas type marker.

Burner Oriﬁce Conversion

1. Remove the screws that secure the fettle and the

burner tube assembly, located behind the burner
tube assembly. Remove the three (3) screws that se-
cure the burner housing assembly to the base pan at
the right and left end of the burner housing assem-
bly. (Fig. 50)

2. Remove the fettle and the burner tube assembly.

Slide the burner housing assembly to the right and
up to free the oriﬁce.

3. Using a 1/2” open end wrench remove the oriﬁces.

(Fig. 51)

4. To convert burner oriﬁces, remove the oriﬁces and

replace with the proper oriﬁce listed in the table on
Page 34.

Mixer Tube Replacement

(Conversion to LP ONLY)

1. Remove the 2 screws from the left end of the burner

��
��
��

Pilot Location

Burner Housing
Assembly

Remove
Screws

Fettle Screw

Fettle

Remove screws

FP1835

Fig. 50

Remove screws holding burner housing assembly and

burner tube assembly.

Fettle Screw

Remove Screws

CO147

Fig. 51

Burner oriﬁce replacement.

��
��
��

Main Burner
Oriﬁce

Burner Tube
Oriﬁce

Содержание TrimWorks DVA4136













































Результаты поиска

Содержание TrimWorks DVA4136

Отзывы:

Похожие инструкции для TrimWorks DVA4136

Бренды по названию

Популярные бренды

Vermont Castings TrimWorks DVA4136, Инструкции по установке и руководство для владельца

Результаты поиска

Содержание TrimWorks DVA4136

Отзывы:

Похожие инструкции для TrimWorks DVA4136

Бренды по названию

Популярные бренды