4
20304852
ICFDV40 Fireplace Insert
IMPORTANT SAFETY INFORMATION & CODE APPROVAL
12. You must keep control compartments, burners, and
circulating air passages clean. More frequent cleaning
may be needed due to excessive lint and dust. Turn off
the gas valve and pilot light before cleaning
fi
replace.
13. Have venting system inspected annually by a quali-
fi
ed service person. If needed, have venting system
cleaned or repaired. Refer to
Cleaning and Mainte-
nance
, Page 38.
14. Keep the area around your
fi
replace clear of combus-
tible materials, gasoline, and other
fl
ammable vapor
and liquids. Do not run
fi
replace where these are used
or stored. Do not place items such as clothing or dec-
orations on or around
fi
replace.
15. Do not use this
fi
replace to cook food or burn paper or
other objects.
16. Never place anything on top of
fi
replace.
17. Do not use any solid fuels (wood, coal, paper, card-
board, etc.) in this
fi
replace. Use only the gas type
indicated on rating plate.
18. This appliance, when installed, must be electrically
grounded in accordance with local codes or in the
absence of local codes, with the
National Electrical
Code, ANSI/NFPA 70
, or the
Canadian Electrical Code,
CSA C22.1.
19. Do not obstruct the
fl
ow of combustion and ventilation
air in any way. Provide adequate clearances around
air openings into the combustion chamber along with
adequate accessibility clearance for servicing and
proper operation.
20. Do not use
fi
replace if any part has been under water.
Immediately call a qualified service technician to
inspect the appliance and to replace any part of the
control system and any gas control which as been
under water.
21. Do not operate
fi
replace if any log is broken.
22. Do not use a blower insert, heat exchanger insert, or
any other accessory not approved for use with this
fi
replace.
23. Do not operate the
fi
replace with glass door removed,
cracked, or broken.
CODE APPROVAL
Direct vent type appliances draw all combustion air from
outside of the dwelling through the vent pipe.
These appliances have been tested by CSA and found to
comply with the established standards for DIRECT VENT
GAS FIREPLACE HEATERS in the USA and Canada as
follows:
LISTED VENTED GAS FIREPLACE HEATER
TESTED TO ANSI Z21.88a-2012/CSA 2.33a-2012
STANDARDS
The installation must conform with local codes or, in the
absence of local codes, with the
National Fuel Gas Code,
ANSI Z223.1/NFPA 54
, or the
National Gas and Propane
Installation Code, CSA B149.1
.
A manufactured home (USA only) or mobile home OEM
installation must conform with the
Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280,
or when such a standard is not applicable, the
Standard for
Manufactured Home Installations, ANSI/NCSBCS A225.1
,
or
Standard for Gas Equipped Recreational Vehicles and
Mobile Housing, CSA Z240.4
.
W
ARNING
Never connect unit to private (non-utility)
gas wells. This gas is commonly known as
wellhead gas.
IMPORTANT:
PLEASE READ THE FOLLOWING
CAREFULLY
It is normal for fireplaces fabricated of steel
to give off some expansion and/or contraction
noises during the start up or cool down cycle.
Similar noises are found with your furnace heat
exchanger or car engine.
IMPORTANT:
PLEASE READ THE FOLLOWING
CAREFULLY
It is not unusual for gas
fi
replaces to give off some
odor the
fi
rst time it is burned. This is due to the
manufacturing process.
Please ensure that your room is well ventilated
during burn off — open all windows.
It is recommended that you burn your
fi
replace
for at least ten (10) hours the
fi
rst time you use it.
Place the fan switch in the “OFF” position during
this time.
DANGER
HOT GLASS
WILL
CAUSE BURNS
.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
