Vermont Castings ExtremeView 33XDV Скачать руководство пользователя

Страница: 40 / 56

XDV Direct Vent Gas Fireplace

10009383

Fuel Conversion Instructions

To convert the XDV units for use with a different gas fol-
low these instructions. Before proceeding, turn control
knob on valve to “

OFF

” and turn gas supply

OFF

. Turn

OFF

any electricity that may be going to the appliance.

CAUTION: Logs may be HOT! Allow to cool before
proceeding.

1. Open louvre assembly bottom to gain access to valve.

Remove window frame assembly. (Refer to “Window
Frame Assembly Removal”, Page 24, Fig. 48)

2. Remove logs if previously installed.

Honeywell Valve

1. Remove cap from HI/LO knob. This can be accom-

plished by lifting the plastic cap off the screw. (Fig.
73)

2. Remove the screw from center of HI/LO knob with

small screwdriver turning counterclockwise. (Fig. 73)

3. Insert conversion screw supplied in conversion kit.

Blue for natural gas, red for LP.

4. Tighten screw, replace cap.

2. Insure the rubber gasket (D) is properly positioned

and install the new HI/LO pressure regulator assem-
bly to the valve using the new screws (E) supplied
with the kit. Tighten the screws securely. (Ref. torque
= 25 in/lb) (Fig. 75)

3. Install the enclosed conversion label (F) to the valve

body where it can easily be seen. (Fig. 75)

Valve conversion is complete.

Conversions must be completed by qualiﬁed personnel

CO100

Gas conversion

HI-LO knob

3/15/99 djt

Hi-Lo Knob

Cap

Lift Open

Fig. 73

Remove center screw from Hi-Lo knob.

Remove

Center Screw

CO100

NOVA SIT820 Valve

1. Using the TORX T20 bit, remove and discard the

three (3) pressure regulator mounting screws (A),
pressure regulator tower (B) and the spring and
diaphragm assembly (C). (Fig. 74)

FC107

SIT820

valve conversion

10/03

OFF

PILO

Fig. 74

Remove mounting screws, pressure regulator tower

and spring and diaphragm assembly.

FC107

FC108

SIT

regulator

conversion

10/03

OFF

PILOT

FC108

Fig. 75

Replace regulator.

Burner Oriﬁce Conversion
33/36XDV

1. Remove bracket rear log and front grate. (Fig. 76)
2. Remove burner housing assembly and front burner

tube. (Fig. 76)

3.  Remove burner oriﬁce from manifold assembly using
  3/8” wrench. (Fig. 76)
4.  Install conversion oriﬁces in place of oriﬁces just

removed.

��
��
��

Fig. 76

Remove manifold assembly.

Rear Burner Oriﬁce:

(Refer to Conversion Kit

Oriﬁce Chart)

Front Burner Oriﬁce:

(Refer to Conversion Kit

Oriﬁce Chart)

Main Burner

Assembly

Pilot

Location

Front Burner

Tube

FP1612

5. Remove air shutters from burner pan by removing

shutter retaining screw then air shutter. (Fig. 77)

6. For 36XDV replace only rear air shutter.
Natural Gas: Rear air shutter, close two sides, top

and bottom open.

Front air shutter, fully open.

Содержание ExtremeView 33XDV

























































Результаты поиска

Содержание ExtremeView 33XDV

Отзывы:

Похожие инструкции для ExtremeView 33XDV

Бренды по названию

Популярные бренды

Vermont Castings ExtremeView 33XDV, Инструкции по установке и руководство для владельца

Результаты поиска

Содержание ExtremeView 33XDV

Отзывы:

Похожие инструкции для ExtremeView 33XDV

Бренды по названию

Популярные бренды