Vermont Castings ExtremeView 33XDV Скачать руководство пользователя | Manualshive

Страница: 30 / 56

background image

XDV Direct Vent Gas Fireplace

30

10009383

Large Lava Rock

The large bag of lava rock provided with this ﬁreplace
must be placed on the ﬁrebox base around the sides of
the burner assembly and on the tray beneath the grate.

Under no circumstances should this large lava rock
be placed on any part of the burner assembly.

Burner Lava Rock Placement

Place the contents of the small bag of ceramic burner
lava embers on the burner in front of the front logs. Do
not place burner lava rock in the inside corners of the
front logs.

Fig. 66

Flame adjustment knob for SIT valve.

LO

HI

FP390

FLAME ADJUSTMENT KNOB

11/21/96

Turn

counterclockwise

to increase

flame height

Turn clockwise

to decrease

flame height

SIT 820 Valve

Fig. 65

Flame adjustment knob for Honeywell valve.

LO

HI

Turn

counterclockwise

to decrease

flame height

Turn clockwise

to increase

flame height

HV102
Honeywell hi/lo knob
4/5/99 djt

Honeywell Valve

Flame & Temperature Adjustment

For ﬁreplaces equipped with Hi/Lo valves, ﬂame adjust-
ment is accomplished by rotating the Hi/Lo adjustment
knob located near the centre of the gas control. (Fig. 65
or 66)

Manual ON/OFF Valve

The Manual ON/OFF valve was designed particularly
for the main burner operation. The main burner ﬂame
can be turned on and off as desired. This valve is rec-
ommended to be set to the “ON” position when lighting
the unit. (Fig. 67)

Flame Characteristics

It is important to periodically perform a visual check of
the pilot and the burner ﬂames. Compare them to Fig-
ures 68-69. If any of the ﬂames appear abnormal call a
service person.

3/8” - 1/2”

(10 - 13 mm)

Fig. 68

Correct pilot ﬂame appearance.

F584-703

SIT Pilot

PSE Pilot

Inspecting the Venting System

This appliance venting system is designed and con-
structed to develop a positive ﬂow adequate to remove
ﬂue gases to the outside atmosphere.
Any foreign objects in the venting system, except those
designed speciﬁcally for the venting system, may cause
spillage of ﬂue gases.
To inspect the venting system, make sure the main gas
valve is off. Remove window frame assembly (Refer to
Window Frame Assembly Removal Section). Using a
ﬂashlight, check the area above the bafﬂe in the com-
bustion dome. Clean if necessary.

FP1613

Fig. 67

Manual ON/OFF valve shown on RN/RP models.

Flame Adjustm

en

t

Fa

n

S

pe

ed

Ignitor

ON

OFF PILOT

ON

OFF

ON

OFF

FP1612
Copreci
manual on/off
valve
4/06

«
...
28
29
30
31
32
...
»

Содержание ExtremeView 33XDV

























































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeView 33XDV

Бренд: Dik Geurts Страницы: 96

Бренд: Astria Страницы: 70

Бренд: Dimplex Страницы: 2

Бренд: Desa Страницы: 44

Simplifyre SFE-ST

Бренд: Hearth and Home Technologies Страницы: 8

Бренд: Dru Страницы: 72

Бренд: Landmann Страницы: 60

Oak Ridge Creek 24”

Бренд: Heatmaster Страницы: 6

Бренд: Jeco Страницы: 4

Бренд: Montigo Страницы: 40

Бренд: Majestic Страницы: 36

Superior Fireplaces DRT63 ST Series

Бренд: IHP Страницы: 2

Бренд: IHP Страницы: 8

Бренд: IHP Страницы: 2

Бренд: IHP Страницы: 24

Бренд: UrbanFire Страницы: 20

Бренд: decorflame Страницы: 30

Бренд: Pacific Living Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды