Vermont Castings ExtremeView 33XDV Скачать руководство пользователя

Страница: 38 / 56

XDV Direct Vent Gas Fireplace

10009383

NOTE: Before troubleshooting the gas control system, be sure external gas shut off is in the “On” position.

SIT NOVA 820 MILLIVOLT VALVE

Troubleshooting the Gas Control System

WARNING: REMOVE GLASS FRONT BEFORE DOING ANY GAS CONTROL SERVICE WORK.

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

1. Spark ignitor will not light

A. Defective or misaligned

Using a match, light pilot. If pilot lights, turn off

electrode at pilot.

pilot and push the red button again. If pilot will not

light, check the gap at electrode and pilot; it should

be 1/8” to have a strong spark.

B. Defective ignitor (Push Button)

Push piezo Ignitor Button. Check for spark at

electrode and pilot. If no spark to pilot, and electode

wire is properly connected, replace ignitor.

2. Pilot will not stay lit after

A. Defective pilot generator

Check pilot ﬂame. Must impinge on thermocouple/

carefully following lighting (thermocouple), remote wall

thermopile. NOTE: This pilot burner assembly

instructions.

switch.

utilizes both a thermocouple and a thermopile.

The thermocouple operates the main valve opera-

tion (ON/ OFF). Clean and/or adjust pilot for maxi-

mum flame impingement on thermopile and thermo-

couple.

B. Defective automatic valve

Turn valve knob to “Pilot.” Maintain ﬂow to pilot;

millivolt meter should read greater than 10 mV. If

the reading is okay and the pilot does not stay on,

replace the gas valve. NOTE: An interrupter block

(not supplied) must be used to conduct this test.

3. Pilot burning, no gas to

A. Wall switch or wires defective

Check wall switch and wires for proper connections

main burner

Jumper wires across terminals at wall switch; if

burner comes on, repalce defective wall switch. If

okay, jumper wires across wall switch wires at valve;

if burner comes on, wires are faulty or connections

are bad.

B. Thermopile may not be

1. Be sure wire connections from thermopile at

generating sufﬁcient

gas valve terminals are tight and thermopile is

millivoltage.

fully inserted into pilot bracket.

2. One of the wall switch wires may be grounded.

Remove wall switch wires from valve terminals if

pilot now stays lit, trace wall switch wiring for

ground. May be grounded to ﬁreplace or gas

supply.

3. Check thermopile with millivolt meter. Take

reading at thermopile terminals of gas valve—

should read 250-300 millivolts (minimum 150)

while holding valve knob depressed in pilot

position and wall switch “OFF.” Replace faulty

thermopile if reading is below speciﬁed minimum.

C. Plugged burner oriﬁce.

Check burner oriﬁces for debris and remove.

D. Defective automatic valve

Turn valve knob to “ON,” place wall switch to “ON” —

operator.

millivolt meter should read greater than 100 mV. If

the reading is okay and the burner does not come

on, replace the gas valve.

4. Frequent pilot outage

A. Pilot ﬂame may be too low

Clean and/or adjust pilot ﬂame for maximum ﬂame

problem.

or blowing (high) causing the

impingement on thermopile and thermocouple.

pilot safety to drop out.

B. Possible blockage of the vent

Check the vent terminal for blockage (recycling the

terminal.

ﬂue gases)

Содержание ExtremeView 33XDV

























































Результаты поиска

Содержание ExtremeView 33XDV

Отзывы:

Похожие инструкции для ExtremeView 33XDV

Бренды по названию

Популярные бренды

Vermont Castings ExtremeView 33XDV, Инструкции по установке и руководство для владельца

Результаты поиска

Содержание ExtremeView 33XDV

Отзывы:

Похожие инструкции для ExtremeView 33XDV

Бренды по названию

Популярные бренды