Vermont Castings ExtremeView 33XDV Скачать руководство пользователя | Manualshive

Страница: 11 / 56

background image

10009383

11

XDV Direct Vent Gas Fireplace

Top Vent Application

Restrictor Plate

When the 33XDV or 36XDV models are installed as top
vent ﬁreplaces with a minimum 12” (305 mm) rise, the
restrictor plate must be installed to give better ﬂame
appearance.
This restrictor plate is shipped with the 33/36XDV and is
located below the access control panel.

33XDV Restrictor Plate Installation

1. Remove rear log bracket located behind the burner

panel.

2. Install the restrictor plate with the rear log using ex-

isting mounting holes and pre-attached screws from
the rear log bracket. (Fig. 15)

3. Install rear log bracket assembly by reversing Step 1.
4. Install log set, ember materials, lava rock. Refer to

log set installation section.

36XDV Restrictor Plate Installation

1. Remover rear log bracket located behind the burner

panel.

2. Replace the deﬂector rear log bracket with the

restrictor plate to the rear log bracket using existing
mounting holes and screws. (Fig. 16) Discard deﬂec-
tor.

3. Install rear log bracket assembly by reversing Step 1.
4. Install log set, ember materials, lava rock. Refer to

log set installation section.

��
��
��

Rear Log Bracket

Restrictor Plate

FP1729

Fig. 15

33XDV restrictor plate installation.

Your ﬁreplace is approved to be vented either through
the side wall, or vertically through the roof.

•

Only CFM Corporation venting components speciﬁ-
cally approved and labelled for this ﬁreplace may be
used.

•

If vent termination is installed in an accessible loca-

tion, Vent Termination Guard #53525 shall be in-
stalled.

•

Vent terminations shall not be recessed into a wall or
siding.

•

Horizontal venting which incorporates the twist lock
pipe must be installed on a level plane without an
inclining or declining slope.

•

Horizontal venting which incorporates the use of ﬂex
venting shall have an inclining slope from the unit of
1/2” (13 mm) per 12” (305 mm).

General Venting

There must not be any obstruction

such as bushes,

garden sheds, fences, decks or utility buildings within
24” (610 mm) from the front of the termination hood.
Do not locate termination hood where excessive snow
or ice build up may occur. Be sure to check vent termi-
nation area after snow falls, and clear to prevent ac-
cidental blockage of venting system. When using snow
blowers, make sure snow is not directed towards vent
termination area.

Location of Vent Termination

It is imperative the vent termination be located observ-
ing the minimum clearances as shown on the next
page.
*Check with local codes or in absence of same with
CSA B149.1 Installation Codes (1991) for Canada
or follow the current National Fuel Gas Code, ANSI
Z223.1/NFPA 54 for installations in the USA.

��
��
��

Rear Log Bracket

Restrictor Plate

FP1730

Fig. 16

36XDV restrictor plate installation.

Remove

and Discard

Deﬂector

«
...
9
10
11
12
13
...
»

Содержание ExtremeView 33XDV

























































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeView 33XDV

Бренд: HAMPTON BAY Страницы: 10

Бренд: CACHFIRES Страницы: 11

Бренд: Jøtul Страницы: 72

Heatilator Icon Series

Бренд: Heatilator Страницы: 2

SOM979PS-36AFCN

Бренд: Sylvania Страницы: 4

341 black beauty slimline

Бренд: Valor Fires Страницы: 40

ECO-prestige 75

Бренд: KAL-FIRE Страницы: 184

Бренд: Jeco Страницы: 3

Бренд: Solas Страницы: 6

Бренд: Nordpeis Страницы: 16

Бренд: Home Decorators Collection Страницы: 24

Бренд: Napoleon Страницы: 40

Бренд: EdilKamin Страницы: 19

Бренд: baltur Страницы: 92

Бренд: ADF Страницы: 17

Бренд: ADF Страницы: 22

Бренд: GlammFire Страницы: 24

Бренд: Panadero Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды