Vermont Castings DVRT36 Скачать руководство пользователя страница 42

Страница: 42 / 50

Vermont Castings, Majestic Products DVRT36/ 39/ 43

10002428

DVRT36/39/43

(continued)

Ref.

Description

DVRT36

DVRT39

DVRT43

27.

FK24 Fan Assembly w/Bracket (Optional)

54103

28.

FK12 Fan Assembly (not shown)

ZA1110

29.

Electric Cord 6’ (Optional) (not shown)

51865

30.

Fan Speed Control (Optional) (not shown)

51738

31.

Fan Speed Control Knob (Optional) (not shown)

51882

32.

Fan Temperature Sensor (Optional) (not shown)

51704

33.

Window Frame Assembly

10001425

10002478

10001805

34.

Lower Window Frame Clamps

54174

35.

Glass w/Gasket (not shown)

54427

54445

54564

36.

Window Glass Gasket (not shown)

57317

37.

Louvre Assembly Top

10000037

10000039

10000041

38.

Louvre Assembly Bottom

10000038

10000040

10000042

39.

Hinge - Bottom Louvre Assembly

52356

40.

Plate, Flue Pipe w/4’ Pipe Assembly

10002509

41.

Plate, Flue Cover (not shown)

10002298

42.

Plate, Air Inlet Cover w/7” Collar (not shown)

10002766

43.

Gasket, Flue Cover Plate (not shown)

10002233

44.

Gasket, Flue Pipe Cover Plate (not shown)

10002237

45.

Gasket, Air Inlet Pipe (not shown)

10002449

46.

Remote ON/OFF Switch (not shown)

51842

47.

Wire Harness - Remote Switch (not shown)

55923

48.

Remote ON/OFF Switch Kit
(Incls. above w/brckt)(not shown)

53875

49.

EB-1 Electrical/Connection Box Kit (Optional) (not shown)

ZA1200

50.

Ceramic Lining Kit (Optional) (not shown)

BT2TBO

CT2TBO

N/A

50a.

Ceramic Lining Kit Standard on DVRT43 (not shown)

N/A

10000459

51a.

RF Valve - Natural

20003719

51b.

RF Valve - LP

20003720

52.

Antennae

20003561

53a.

Pilot - RF - Natural (3 Way)

20002266

53b.

Pilot - RF - LP (3 Way)

20002268

54.

Transmitter

20002047

55.

Cord Set

20002541

56.

Thermopile

20002400

57.

Pilot Tube 1/8” x 24” Long w/ Fittings (PSE Pilot)

10003279

58a.

Pilot Assembly, SIT Top Convertible EN

10002387

58b.

Pilot Assembly, SIT Top Convertible EP

10002388

59.

Cable Igniter, EN & EP (not shown)

10000696

60a.

Gas Valve, SIT 822 EN

57884

60b.

Gas Valve, SIT 822 EP

57883

61.

Sensing Electrode (with Cable) EN & EP (not shown)

57885

62.

Transformer, EN & EP

7522409

63.

Ignition Module, Honeywell, EN & EP

20000005

64.

Wire Harness, Honeywell, EN & EP (not shown)

10001979

65.

Relief Plate with Gasket Assy Burner Tray

10004192

66.

Ignition Synetek EN & EP (not shown)

57899

67.

Wiring Harness, Synetek EN & EP (not shown)

10000417

Содержание DVRT36



















































Результаты поиска

Содержание DVRT36

Отзывы:

Похожие инструкции для DVRT36

Бренды по названию

Популярные бренды

Vermont Castings DVRT36, Руководство пользователя и инструкция по установке для владельцев жилья

Результаты поиска

Содержание DVRT36

Отзывы:

Похожие инструкции для DVRT36

Бренды по названию

Популярные бренды