26
Vermont Castings, Majestic Products DVRT36/ 39/ 43
10002428
Installation of Logs & Lava Rock
DVRT39 - Refer to Figure 44.
1. Remove the top louvre assembly.
2. Remove the window frame assembly.
3. Fit the rear log (B35) onto the rear log support. The
two (2) holes in the log locate on the two (2) studs
on the support.
4. Fit the right-front log (B36) onto support bracket
over the right side of the burner housing assembly.
The two (2) holes in the log locate over the two (2)
studs of the bracket.
5. Fit the left-front log (B37) onto the support bracket
over the left side of the burner housing. Again, the
two (2) holes in the log locate on the two (2) studs
on the bracket.
6. Place the left-top log (B38) in place. The notch
along the lower front edge sits against the front
grate (Fig. 44), and the top of the log sits in the
cutout on the inner end of log B37.
7. Scatter the Ceramic Ember Rocks (Part #57897)
over the burner housing assembly in the areas
between the logs. Refer to shaded areas in Figure
44.
8. Scatter the lava rock (Part #10001454) around the
base of the firebox area. Do not place any of this
material on the burner housing assembly.
NOTE: Glowing lava rock for DVRT39 is only
allowed to be positioned at the front area (radiant
portion) of the burner housing assembly.
Do not mix the lava rock materials. Lava
rock from the package labeled with Part
#10001454 must not be placed on the
burner housing assembly.
Unpack the logs from their shipping box. Remove each
log from its wrapping material.
Dispose of the plastic bags and
wrapping in a safe manner. Keep the
logs and plastic bags away from
children.
Take care handling the logs as the material is fragile.
The individual logs can be identified by the number
cast into the underside of each log.
DVRT36 - Refer to Figure 43.
1. Remove the top louvre assembly.
2. Remove the window frame assembly.
3. Fit the left-rear log (B43) to the left side of the rear
log support. The two (2) holes in the log locate on
the two (2) studs of the support.
4. Fit the right-rear log (B31) to the right side of the
support. The two (2) holes in the log locate over the
two (2) studs of the support.
5. Fit the left-front log (B32) to the support bracket
over the burner housing. Again, the two (2) holes in
the log locate on the two (2) studs on the bracket.
6. Place the left-top log (B33) across the left front
and rear logs. (Fig. 43) The hole under the end of
this log locates over the knob on the left rear log.
The forward end of log B33 rests in the cutout in the
left front log.
7. Place the right-front log (B34) in position by
resting the ‘heal’ of the log between the outside and
first prong of the front grate and laying the log down
in the cutout of the right rear log. (Fig. 43)
8. Scatter the Ceramic Ember Rocks (Part #57897)
over the burner housing assembly in the area
forward of the front logs. Refer to shaded areas in
Figure 43.
9. Scatter the lava rock (Part #10001454) around the
base of the firebox area. Do not place any of this
material on the burner housing assembly.
NOTE: Glowing lava rock for DVRT36 is only
allowed to be positioned at the front area (radiant
portion) of the burner housing assembly.
Do not mix the lava rock materials. Lava
rock from the package labeled with Part
#10001454 must not be placed on the
burner housing assembly.
B43
B31
B32
B34
B33
Front Grate tines
Ceramic Ember Rocks
LG227
Fig. 43 DVRT36 logset and ember placement
