Vermeer S925TX Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 104

Vermeer S925TX Скачать руководство пользователя страница 70

40-6 Preparation

S925TX Mini Skid Steer

Gas

Fiber Optic

Jobsite Assessment

Examine work area for any obstructions, conditions, or situations which may impair machine operation or
create a safety hazard for the operator or other persons. Use the information in this manual combined with your
own good judgment when identifying these hazards and implementing hazard avoidance measures.

Check for steep slopes, banks, overhangs, drop-offs, and trenches which can cave in.

DANGER:

Gas explosion can kill. If you strike a gas line, shut off engine and evacuate area

immediately. Contact utility company and do not return until the utility company gives
permission to do so.

WARNING:

Laser light may damage eyes. Do not look into the end. Fiber optic cables carry

laser light which may damage your eyes. If you are not sure what type of cable it is, do not
look into the end. Contact appropriate utility company for assistance.

WARNING:

The weight of your machine may cause the ground to give way. Machine can

fall and tip over. Death or serious injury could result. Keep well away from cliff edges. Do
not dig under the machine or attachment. Take care when backfilling. Do not go too close
to edges. Do not drive or operate on unstable ground.

«
...
68
69
70
71
72
...
»

Содержание S925TX









































































































Отзывы:

Нет отзывов