Verdemax 4330, Руководство по эксплуатации, Страница: 19 / 20

19
the spool base drum A, B, C, D one-to-one match, use screws
(5) to fix them together.
Install additional handle (Fig. 4)
Put the D type handle base to the gap of the handle bracket,
aligh the hole of the handle (4) and the bracket (5), use
knob (3) and nut (18) to assemble the handle tighten enough.
Attention: The rubber side of the handle is in the side of the
spool, while the groove side of the handle face to operator.
Putting the machine in operation
(Fig. 5 and 6)
• Insert the charged battery in the strimmer until the
interlock (15) latches. The rechargeable battery can only
be inserted in the strimmer in one position (Fig.5).
Attention: When inserting the battery do not actuate
the switch-on inhibit (2) and the on/off switch (1).
• Adopt a safe stance. Hold the strimmer in both hands.
Do not set the cutting device down on the ground. Press
the switch-on inhibit (2) to right and actuate the switch
(1) (Fig. 6). After switching on, the switch-on inhibit (2)
must no longer be held.
• In order to switch off, release the switch (1) (Fig. 6).
Attention:
On/off switch can only be activated after the
switch-on inhibit (2) is pressed.
Directions for set lenght adjustment and the use of the
set as edge cutter
(Fig. 7, 8, 9, 10)
The tube length may be adjusted to suit your height
(Fig. 7):
• To do so, turn the ribbed plastic sleeve clockwise to loosen
the connection. Adjust the tube to the suitable length
and fasten the connection by turning the tapped sleeve
anti-clockwise.
Adjusting the tilting angle
(Fig. 8):
• Press the button (8) - the strimmer head is disengaged
and can be pivoted in 72
°
relative to the shaft.
Adjusting for edge trimming (Fig. 7, 8 , 9, 10):
• Set the tilting angle as previously described.
• Press the edge cutter adjustor (11) and rotory the handle
with clockwise with 180
°
, then the edge cutter spool
would directs to ground. It’s for edge trimming.
Instructions for operating the mowing machine
(Fig.11):
• Move the mowing machine evenly from oneside to
another.
• If possible, mow by using the left half of the mowing ma-
chine. The mowed parts of plants and / or stones will
thus be hurled forward away from the operating person.
• The best possible cutting result are achieved when you hold
the trimmer with an angle of 20
°
- 30
°
to the left side.
• Avoid contact between the mowing string and obsta-
cles such as fences, walls, stones, etc. This leads to
excessive wear and tear.
Changing the spool
(Fig. 12)
Attention - risk of injury! Always remove the re-
chargeable battery from the device before all work.
Press the nylon spool head cap claw (2) and pick out the
worn spool (3), replace a new spool to the spool frame (4)
with the line out of the hole of the spool frame, and replace
the cap (1) to the nylon head.
Attention:
The nylon head is with single line, not double.
Maintenance and care
Attention - risk of injury!
Always remove the re-
chargeable battery from the device before all work.
Clean your battery-operated mowing machine thoroughly
each time after you use it. Remove the grass and dirt. Clean
the ventilation openings. It is best to clean the plastic parts
with a wet cloth and a soft detergent. Never use aggressive
detergents or solvents. Do not pour water into the machine
and do not sprinkle it with water. Store the mowing machine
in a dry place, never expose it to frost and keep it out of
children‘s reach.
For more extensive maintenance or repairs, give the mowing
machine to the service center.
Repair service
Repairs to electric power tools should only be carried out
by a specialised electrician.
Information for environmental protection/disposal
Dispose of the machine properly after it is worn out. Dis-
connect the mains cable in order to prevent misuse. Do not
dispose of the machine with the household waste. In the
interest of environmental protection, take it to a collection
point for electric machines. Your responsible local authority
can provide you with addresses and operating times. Also
take the packaging materials and worn out accessories to
the appropriate collection points.
Only for EU countries
Do not discard electric tools in the household
waste!
In accordance with European Directive 2012/19/EC on
waste electrical and electronic equipment and its im-
plementation in national law, waste electric tools must be
collected separately for environmentally-compatible re-use.
Recycling alternative to the return invitation:
Instead of returning the electric equipment, the owner is
alternatively obligated to take part in the proper recycling
in the case of relinquishment of ownership. The waste
equipment can also be taken to a collection facility which
disposes of it in the sense of the national recycling man-
agement and waste acts. This does not pertain to the
accessory parts and auxiliary equipment without electri-
cal components accompanying the waste equipment.