background image

ZEC410 VAV Controllers Installation Instructions

16

To ensure the best bus performance, set sequential  device addresses with no gaps in the device address range 
(4, 5, 6, and so on). The field controllers  do not need to be physically connected on the bus in their numerical 
device address order.

4.

Write each field controller’s device address on the  white label below the DIP switch block on the controller’s 
cover.

Refer to the 

MS/TP Communications Bus Technical  Bulletin (LIT-12011034) 

for more information on field  controller 

device addresses and how to set them on MS/TP Bus devices.

Accessories

Table 3 lists the ZEC controller accessories. 

Operation

The ZEC controller is pre-programmed for the VAV box operating sequence as ordered. You do not need to 
program the controller; however, you need to provide configuration information using either the Balancing Sensor 
or the Zone Setup screen on the Verasys System Smart Building Hub.

For detailed information on Verasys

 

System, including dehumidification capability, DCV, occupancy sensing, and 

general operating modes, refer to the Verasys

 System Operation Overview Technical Bulletin (LIT-12012370)

.

Table 3:  Zone Controller Accessories

Product Code 
Number

Description

Zone Temperature Sensors (Hardwired)

TE-68NT-0N00S

Wall temperature sensor, 1k ohm, nickel with temperature occupancy button.

TE-68NT-1N00S

Wall temperature sensor, 1k ohm, nickel with warmer/cooler (W/C) adjustment and temperature 
occupancy pushbutton.

Zone CO

2

 Sensor

NS-BCN7004-0

BACnet network CO

2

 sensor designed to function directly with Johnson Controls BACnet MS/TP digital 

controllers, in a 80 mm x 120 mm (3 in. x 4.5 in.) enclosure with terminal block and modular jack wiring 
connections.
Only addresses 212 to 214 are supported.

Second Zone Damper Actuator

1

1. You must purchase the actuator and add it to a damper without a ZEC310 controller.

M9106-GGA-2

6 n•m torque non-spring return damper actuator

Network Sensors for Zone Temperature

NS-BTB7003-0

Network sensor, 120 x 80 mm (4.7 x 3.1 in.), Johnson Controls® logo, local setpoint, terminals

NS-BTB7003-2

Network sensor, 120 x 80 mm (4.7 x 3.1 in.), no logo, local setpoint, terminals

NS-BTN7003-0

Network sensor, 120 x 80 mm (4.7 x 3.1 in.), no logo, no setpoint, terminals

NS-BTN7003-2

Network sensor, 120 x 80 mm (4.7 x 3.1 in.), no logo, no setpoint, terminals.

NS-BTP7002-0

Network sensor, 120 x 80 mm (4.7 x 3.1 in.), Johnson Controls logo, Warmer/Cooler adjustment, 
terminals

NS-BTP7002-2

Network sensor, 120 x 80 mm (4.7 x 3.1 in.), no logo, warmer/cooler adjustment, terminals

Occupancy Lighting Switch

NS-BCN7004

Occupancy sensing light switch for control of indoor incandescent and fluorescent lights

RIBU1C

Enclosed relay for OLS-2100-1 sensor

Balancing Tool

NS-ATV7003-0

Handheld VAV balancing tool

Содержание ZEC410




















Отзывы: