Veolia ELGA CENTRA-LDS-US Скачать руководство пользователя страница 29

Страница: 29 / 57

ELGA

CENTRA – MDS/LDS/RDS US Operator Manual

CENTRA – MDS/LDS/RDS US Version 01 – 08/14

Page 23

Step 5 - Volume/flow - displayed unit of measurement

The reservoir volume and recirculation flow can be
displayed in either liters (L) or US Gallons (USG).

PRESS SCROLL

to change mode (L or USG)

PRESS TICK



to proceed to step 6.

PRESS TICK



Note: Proceed to step 13 for MDS and LDS variants.

Step 6 - Pressure - displayed unit of measurement (RDS)

The loop pressure can be displayed in either bar (bar) or
pounds per square inch (psi).

PRESS SCROLL

to change mode (bar or psi)

PRESS TICK



to proceed to step 7.

PRESS TICK



Step 7 - Water purity unit setting (RDS)

This screen allows preferred displayed units of water
purity to be set, to either,

Ω

.cm

µS/cm

. This only

affects the quality measurement in the recirculation loop.

PRESS SCROLL

to change mode (M

Ω

.cm or

µS/cm)

PRESS TICK



to proceed to step 8.

PRESS TICK



Step 8 - Uncompensated water quality (RDS)

A U will indicate uncompensated readings (recirculation
loop only) in the normal process screen.

PRESS SCROLL

to change mode

(



= Uncompensated water quality ON)

PRESS TICK



to proceed to step 9.

PRESS TICK



Note: The on-going display of uncompensated values is

generally not recommended as it can lead to
confusion among users and increase the
possibilities of using water of inadequate purity.

Pressure measurement screen

Water purity screen

Uncompensated water quality

screen

Volume/flow measurement screen

Содержание ELGA CENTRA-LDS-US


























































Результаты поиска

Содержание ELGA CENTRA-LDS-US

Отзывы:

Похожие инструкции для ELGA CENTRA-LDS-US

Бренды по названию

Популярные бренды

Veolia ELGA CENTRA-LDS-US, Руководство оператора

Результаты поиска

Содержание ELGA CENTRA-LDS-US

Отзывы:

Похожие инструкции для ELGA CENTRA-LDS-US

Бренды по названию

Популярные бренды