Ventilair Comair Aquacom Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 30

Ventilair Comair Aquacom Скачать руководство пользователя страница 6

6

-

Installing,

operating

and

effectuating

maintenance of the Aquacom must  always be
done  by  a  certified  installer,  unless  minor
maintenance  is  concerned  and  is  indicated  as
such in this manual.

-

During  installation  the  local  and  general
applicable  building,  safety  and  installation
instructions  of  the  municipality,  utilities  and
other agencies must be abided.

-

There should not be made any modifications
to the Aquacom.

-

We  recommend  you  to  close  a  service
contract,  so  you  are  assured  of  a  regular
checks.  Contact  your  dealer  for  a  list  of
certified installers.

2.6 Warranty

Comair  provides  a  guarantee  of  2  years  after
installation  to  a  maximum  of  30  months  after
production  date  of  the  Aquacom.  This  warranty
applies  only  to  material  and/or  construction
defects. If there is any defect within the  warranty
period, this must be reported to the installer of the
unit.

The warranty on the unit expires if:
1.

The warranty has expired.

2.

The installation, use and/or maintenance does
not meet the requirements listed in this guide.

3.

Major  maintenance  on  the  unit  was
committed  by  an  unauthorized  maintenance
technician.

4.

There are signs of abuse or modifications on
the device.

5.

Changes to the system have been made after
completion of the installation.

6.

Improper tubing is used.

7.

Too little or improper anti-freeze is used.

2.7 Liability

The  Aquacom  is  designed  as  an  addition  to  a
balanced  ventilation  system.  The  unit  has  to  be
placed  in  a  dry,  frost-free  area  .  Any  other  use  is
unauthorized and is considered as "improper use".
For  damage  or  injury  resulting  from  this  improper
use  of  the  Aquacom,  Comair  cannot  be  held
responsible.

In  addition,  Comair  BV  not  liable  for  damage  or
injury  resulting  from  failure  to  follow  safety,
operating  and  maintenance  instructions  as
specified in the installation manual.

2.8 Deliveries

All deliveries are subject to the general conditions
of METAALUNIE. Afree copy will be sent to you
when requested.

«
...
4
5
6
7
8
...
»

Содержание Comair Aquacom































Отзывы:

Нет отзывов