manualshive.com logo in svg

Ventilair Comair Aquacom, Руководство пользователя, Страница: 19 / 30

Поделиться
Скачать
Ventilair Comair Aquacom Скачать руководство пользователя страница 19

 

 

 

19 

 

5.2.2 Sensor error  

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

This 

scheme 

is 

meant 

for 

the 

installer only.  

Maintenance 

performed 

by the end user is not only 
dangerous,  but  also  has 
disadvantageous 

conse-

quences for the warranty. 

Wire break or short circuit on 

sensor (T1 of T2) 

Does the error indicate 

the other sensor now 

Yes 

No 

Open the front cover using the clip 

locks and open the control unit 

Is the cable broken 

Yes 

Nee 

Replace the 

control unit and 

put the plug back 

in the socket 

Place a new sensor or repair the cable 

and put the plug back in the

 

socket  

 

Pull the plug out 

of the socket 

Pull the plug out 

of the socket 

Temporarily change the wires 

of sensors T1 and T2 and 

restart the unit 

Place a new sensor 

in the right place 

and put the plug 

back in the socket 

Check the cable of the relevant senor for 

an open line error  

Pull the plug out 

of the socket 

Содержание Comair Aquacom































Отзывы:

Нет отзывов