Velocity VDOT-H2 Скачать руководство пользователя страница 21

Страница: 21 / 21

GLT-299-7-2(3) Rev.0

Mar 23, 2018

Type of device is assigned to the detectors as below.

VDOT-H2:

133

VDOT-H2-H: 134

Pressing any key at any time during the information collection cycle, forces the VDOT-AD2 to
display the address, and await new address selection.

Set new address

1. +100, +10, +1 keys are used to select the new address.
2. Press the [Set] key

The buzzer sounds, and all LED’s are turned off. The VDOT-AD2 then starts transmitting to the
detector.

b) Do not remove the detector.

The 7 segment LED shows the new address and “complete” LED lights. If an unsupported or
defective device is connected the buzzer sounds, ERROR LED is lit and the 7 segment LED reads
ERROR CODE.

4. To continue changing the address for another device, change the detector and then repeat from

paragraph 3.

To finish changing addresses, turn the POWER SW off.

Содержание VDOT-H2






















Результаты поиска

Содержание VDOT-H2

Отзывы:

Бренды по названию

Популярные бренды

Velocity VDOT-H2, Инструкция по эксплуатации

Результаты поиска

Содержание VDOT-H2

Отзывы:

Бренды по названию

Популярные бренды