Velocity VDOT-H2 Скачать руководство пользователя страница 2

Страница: 2 / 21

GLT-299-7-2(3) Rev.0

Jun 12, 2018

1.3

VDOT-H2 and VDOT-H2-H common features

* Low profile, stylish appearance

* Soft addressing

* Low monitoring current

* Supplied with protective dust cover

* OMNIVIEW

360 ° LED Indicator for polling and fire alarm indication

Section 2

– GENERAL OPERATION

The

VDOT-H2

heat detector initiates an alarm in response to both 8.3 °C (15 °F) rate-of-rise temperature or a 57 °C

(135 °F) fixed temperature alarm point.

The

VDOT-H2-H

initiates an alarm in response to 83 °C (181 °F). Heat detector incorporates a highly linear

thermistor circuit, with the thermistor mounted externally. The specially designed cover protects the thermistor while

allowing maximum air flow. The thermistor circuit produces a voltage proportional to temperature which is scaled, and

transmitted as a digitally encoded value to the control panel.

Содержание VDOT-H2






















Результаты поиска

Содержание VDOT-H2

Отзывы:

Бренды по названию

Популярные бренды

Velocity VDOT-H2, Инструкция по эксплуатации

Результаты поиска

Содержание VDOT-H2

Отзывы:

Бренды по названию

Популярные бренды