Velleman CAMCOLD17, Руководство пользователя, Страница: 4 / 19

CAMCOLD17
15/05/2009 ©2008 Velleman
®
Components nv
4
• Be very careful not to touch any other part inside the housing while setting the switches, as damage
might occur.
• D1~D7 are used to set the ID of the device, allowing for a system with up to 64 unique devices. Refer
to the table below (
Θ indicates dipswitch in the ON-position).
• The devices can be controlled using a Pelco controller (not included, e.g. CAMCOLSD1C, CAMCOLD/CK)
or a DVR (not included, e.g. DVR4MQAEE, DVR4H, 3GSYSTEM, DVR8N2).
Note: when using an IR remote control device (not included, e.g. CAMCOLD17RC), only the 9 first
(lowest) IDs can be controlled.
ID D7 D6 D5 D4 D3 D2 D1 ID D7 D6 D5 D4 D3 D2 D1
01
Θ 33 Θ Θ
02 Θ 34 Θ Θ
03 Θ Θ 35 Θ Θ Θ
04 Θ 36 Θ Θ
05 Θ Θ 37 Θ Θ Θ
06 Θ Θ 38 Θ Θ Θ
07 Θ Θ Θ 39 Θ Θ Θ Θ
08 Θ 40 Θ Θ
09 Θ Θ 41 Θ Θ Θ
10 Θ Θ 42 Θ Θ Θ
11 Θ Θ Θ 43 Θ Θ Θ Θ
12 Θ Θ 44 Θ Θ Θ
13 Θ Θ Θ 45 Θ Θ Θ Θ
14 Θ Θ Θ 46 Θ Θ Θ Θ
15 Θ Θ Θ Θ 47 Θ Θ Θ Θ Θ
16 Θ 48 Θ Θ
17 Θ Θ 49 Θ Θ Θ
18 Θ Θ 50 Θ Θ Θ
19 Θ Θ Θ 51 Θ Θ Θ Θ
20 Θ Θ 52 Θ Θ Θ
21 Θ Θ Θ 53 Θ Θ Θ Θ
22 Θ Θ Θ 54 Θ Θ Θ Θ
23 Θ Θ Θ Θ 55 Θ Θ Θ Θ Θ
24 Θ Θ 56 Θ Θ Θ
25 Θ Θ Θ 57 Θ Θ Θ Θ
26 Θ Θ Θ 58 Θ Θ Θ Θ
27 Θ Θ Θ Θ 59 Θ Θ Θ Θ Θ
28 Θ Θ Θ 60 Θ Θ Θ Θ
29 Θ Θ Θ Θ 61 Θ Θ Θ Θ Θ
30 Θ Θ Θ Θ 62 Θ Θ Θ Θ Θ
31 Θ Θ Θ Θ Θ 63 Θ Θ Θ Θ Θ Θ
32 Θ 64 Θ
• D8: Baud rate: ON = 4800bps; OFF = 2400bps
• D9: Protocol: ON = PELCO_P protocol; OFF = PELCO_D protocol
• D10: Termination: ON = 120 Ω terminal resistor; OFF = high resistor
Note: 1 camera must terminate the databus with a 120 Ω resistor; all other cameras on the databus
must have a high input resistor.
Factory settings: PELCO_D, 2400bps, ID #01
D10 D9 D8 D7 D6 D5 D4 D3 D2 D1
Θ Θ