VEGA
45
F1 Tempo:
Its default setting is 120 bpm. This value can be modified using the
SLOW
and
FAST
or
VALUE +/-
push buttons.
F2 Time Signature:
This establishes the musical division. The values can be modified using the
VALUE +/-
push buttons and by pressing
F2
Time Signature
again to change the position in the division.
F3 Autocrash:
If enabled (√), a 'Crash' will be played automatically at the end of every Fill In, Break and Intro.
F4 Crash Level:
This establishes the Crash volume related to the Autocrash. It is modified using the
VALUE +/-
push buttons.
F5 Escape:
This is used to return to the main
Edit Pattern
menu.
F8 Bas Octav:
This is used to define the octave in which the fundamental note of the bass is found. The value is modified by repeatedly
pressing the
F8 Bass Octave
function push button to toggle within various values.
F9 Bass Type:
While a bass with four strings cannot go below the note E0, a bass with five strings can go down to note C0. In other words
by choosing a 4-string bass the bass note will not go below E0 and if you change to a 5-string bass the lowest note will be
C0. Pay attention also to the
F8 Bass Octave
value, which could cancel the choice of the
Bass Type
. To select a
Bass Type
press the
F9 Bass Type
function push button repeatedly.
F10 Save:
This is used to save all the parameters modified.
All the lead tracks and respective harmonization and
Retrigger
modes are shown in the middle of the display. To move around within these
parameters, use the
/-
push buttons and use the
VALUE +/-
push buttons to modify their status.
The harmonization mode that will also be seen in the Arrange Mode menu is used to choose between two types of harmonization of the notes:
Close
is used to stay as near as possible to the notes even when the chord played is further away.
Parallel
on the other hand is used to
shift/transpose the notes without altering their intervals. Generally the more musical results are obtained with the
Close
mode.
With the
Retrigger
mode set to On, when the chord is changed, the fundamental note for the bass track is always played and the notes pro-
grammed on the Chord track found in the first measure are repeated instantly.
HOW TO RECORD A PATTERN PART
After having chosen the Pattern to modify, press
F1 Record
to record a
Part
.
Select which section to be record using
F1
and the
VALUE +/-
push buttons.
Select the tonality of the chord for the track to be recorded using
F3 Tonality
(Major, Minor or Seventh). In normal conditions with “M.m.7th”,
the Pattern will record a single chord valid for all the tonalities. In this case, the chord programmed must strictly be DO/C major so that the
VEGA can then use this to correctly interpret for all other variations of the chord during standard arranger playback.
From the
F1 Record
menu, select the track to be recorded using the
/-
push buttons.
The voice of the track selected can be changed simply by calling it up using the
VOICE
push buttons and relative function push buttons. Once
you have made your choice, press
EXIT
to return to the previous menu.
Enable the metronome (which will help you maintain timing during the recording) using
F4 Metronome
.
Switch
F8 Rec/Play
to
Rec
.
Press the
START
push button to start recording. After one pre-count you can start recording.
Upon completion of the number of beats available the recording will stop and automatically the VEGA will switch to
Play
mode.
Press
START
to play back all recorded notes and play a chord on the left part of the keyboard. The track reproduction will loop around the set
number of measures until
START
is pressed again.
Save the whole recording within the current Pattern using
F5 Save
.
F3 PART CLEAR
From the initial page of
Edit Pattern
you can access this page to cancel the whole contents of a single
Part
. Simply press the function push
button relative to the
Part
, after having selected any variations and press
F10 Execute
to cancel.
F1 Global:
deletes the data of all Parts.
F2 Intro:
This is used to select Intro 1, 2, 3, by pressing
F2 Intro
repeatedly.
F3 Fill In:
This is used to select Fill In 1, 2, 3, 4, by pressing
F3 Fill In
repeatedly.
F4 Ending:
This is used to select Ending 1, 2, 3, by pressing
F4 Ending
repeatedly.
F5 Escape:
This is used to return to the Edit Pattern page.
F6 Arrange A:
This is used to select Arrange A.
F7 Arrange B:
This is used to select Arrange B
F8 Arrange C:
This is used to select Arrange C
F9 Arrange D:
This is used to select Arrange D
F10 Execute:
This is used to cancel the
Part
selected at the time.
Pattern Edit
Содержание Ketron
