background image

54

EMR

3

 Troubleshooting Guide

Most errors are the result of poor terminations of wiring, either in a junction box, or at the terminal strips in the IB 
box or Display Head.

Testing an EMR³ System

DISPLAY HEAD 

To perform a Display Head Complete Self-Diagnostic Check, cycle power to the EMR³ system. To cycle power, 
turn the power off for at least 20 seconds before turning it on again. During power up, each Display Head 
automatically tests all its own circuit board hardware in about 30 seconds. If a failure occurs, an error code 
number described in this guide, is posted on the display.

LCD DISPLAY 

To test the LCD Display, simulate a delivery by performing a START and FINISH sequence in Volume or Currency 
mode. The fueling nozzle icon will appear after pressing the START button. For a brief period of time, all of the 
segments will turn on, then off. If the unit fails to perform this test, press the FINISH button once, then press 
START and FINISH again. The nozzle icon should appear after START and disappear after FINISH, if not then the 
head will need to be replaced. 

PULSE GENERATOR INPUT CHECK 

With the cover open and the unit NOT in C&C mode, disconnect the spring between the pulse generator and the 
input shaft. Push start and turn the pulse generator shaft until a nonzero reading appears on the register portion of 
the display. Press the FINISH button, the nozzle icon turns off and a delivery ticket is printed. BE SURE TO 
RECONNECT THE SPRING BEFORE REPLACING THE LID. 

PRINTER CHECK 

Verify ticket printing by either printing duplicate tickets or by simulating a delivery as noted above. Push the FINISH 
button to display a previous delivery on the register display. To print a duplicate ticket, hold the FINISH button 
down for a few seconds then release it.

EMR³ Informational Messages

All messages appear in the Display Head’s 14-character Descriptor Field (ref. Figure 1 on page 4). System 
messages can be either informational or describe an error detected by the self-checking functions of the EMR³.

Information messages do not inhibit the operation of the EMR³.

NO RECORDS 

Inside the Display Head there are zero transactions stored. This message appears in the Setup Mode, when the 
user attempts to printout or view transaction records on a new start-up or after clearing NVRAM by using the 
RESTART feature in C&C mode. This message does not apply to the transaction records stored in the IB and IB 
records can be restored back to the Display Head.

RECALCULATING 

While in the C&C Mode this message is displayed during the meter calibration procedure when new calibration 
points are calculated. Each point takes a few seconds to calculate.

Содержание EMR3 XStream-PKG







































































Отзывы: