background image

 

Warnings and Important Notes

Introduction

2

Warnings and Important Notes

Important 

Failure to install this product in accordance with its instructions and warnings will 
result in voiding of all warranties connected with this product.

To help ensure proper installation and unit performance, we recommend that a Veeder-
Root Authorized Service Contractor install this equipment.

Turn Power Off

Live power to a device creates a potential shock hazard. Always turn power off to the 
device and associated accessories when servicing the unit.

Wear Eye Protection

Fuel spray from residual pressure in the lines can cause serious eye injuries. Always 
wear eye protection.

Injury

Careless or improper handling of materials can result in bodily injury.

Gloves

Wear gloves to protect hands from irritation or injury.

OFF

WARNING

This product is to be installed in systems operating near locations 
where highly combustible fuels or vapors may be present. 

Fire or explosion resulting in serious injury or death could result if the 
equipment is improperly installed or modified. Serious contamination 
of the environment may also occur.

1. Read and follow all instructions in this manual, including all 

safety warnings.

2. Comply with all applicable codes including: the National 

Electrical Code; federal, state, and local codes; and other 
applicable safety codes. 

3. Do not alter or modify any component or substitute components 

in this kit. 

4. Do not use this component for other systems aside from the TLS 

Console. Install only as described in this manual. 

Содержание 847970-001





















Отзывы: