background image

1.

INTRODUCTION

Congratulations on purchasing the (VEC142) Vector Corded, Cordless and
Rechargeable High Intensity 12 Volt DC WorkLight. On the job or around the house,
this work light provides ample light to whatever project you may tackle.  It is easy to
adjust the light angle and comes with a clamp and hook that allow for positioning the
light for hands-free operation. It uses a powerful, proven-technology, rechargeable, non-
spillable, sealed, 12 volt lead acid battery that provides for years of dependable use,
recharge after recharge. The VEC142 is versatile, practical and the perfect choice for:
travel, camping, picnicking, tailgate parties and boating. This work light gives you the
kind of light you need, when and where you need it.

The WorkLight includes one 12 volt DC and one 110/120 volt AC adapter. This permits
recharge flexibility for use around home, business or in the field.  12 volt DC power is
available from most vehicles, boats, jump starters and portable battery packs. Vector
has a variety of portable power products that would make ideal companions.

2.

FEATURES

• Corded, Cordless and Rechargeable for portability
• Powerful 500 watt quartz halogen bulb
• Clamp and hook adapter for versatile mounting options
• Also functions as a 12 volt DC portable power supply
• Reflector swivels and tilts for exact light placement
• Rubber safety guard (bezel) and plastic cage protect the work light
• Toggle power switch – WorkLight ON/OFF 

2.

OPERATION

A two-position “on/off” switch controls the operation of the WorkLight. The WorkLight
can be continuously lit for up to 25 minutes on a full battery charge. Never operate the
WorkLight during AC charging.  FIGURE 1 shows the adjustable angle range of the
WorkLight. FIGURE 2 rearview, shows WorkLight/on/off switch, 12 volt DC socket,
battery charging LED, light angle adjusting thumb screw and the clamp and hook
accessory.
The WorkLight head can swivel 180 degrees, up and down, to accommodate most any
job lighting situation. To release the swivel head from a locked position, simply rotate
the thumbscrew counter-clockwise to loosen.  Then position the swivel head in the
desired position and tighten the thumbscrew to hold in place. An additional benefit of
the WorkLight is the utility value of the clamp and hook accessory.  Utilizing this
accessory provides many mounting (positioning) options that can allow for hands-free
operation.  

2

1

IMPORTANT SAFETY INFORMATION

PLEASE READ INSTRUCTION MANUAL COMPLETELY FOR ALL SAFETY

AND WARNING INSTRUCTIONS.

1.

WARNINGS

• Contains non-spillable, sealed, lead acid battery. Must be recycled or 

disposed of properly.
• DO NOT dispose of batteries in fire or intense heat, as this may result in an
explosion.
• DO NOT open battery or short circuit, as this may cause the battery to leak
or get hot, causing personal injury. Any disposal questions call toll-free
(877) 288-7722.
• USE ONLY WITH CHARGERS PROVIDED WITH UNIT.
• AFTER AC AND DC RECHARGE- disconnect cord and wait 5 minutes before use.
• DO NOT OVERCHARGE:

a) AC charge 15 hours maximum.
b) DC charge 3 hours maximum.

1.

CAUTIONS

1) Do not substitute power cords or adapters. ONLY recharge with supplied AC and

DC recharge adapters. Charge adapters for this unit supply 12 volts DC. 

2) Do not submerge in water. This unit is not waterproof - it is water resistant.
3) Do not operate work light while recharging. This will prevent battery recharge 

and overheat the charging adapters.

4) WorkLight Lens gets very hot when “on”.  Do not touch lens - keep children away

from worklight.

5) Keep combustibles away from WorkLight lens - extreme heat can cause fires. 

This is not a toy!

6) Keep sharp objects away from breakable glass lens.
7) Do not drop or throw spotlight, it contains glass and a sealed lead acid battery.
8) Dispose of unusable batteries in a responsible manner (see battery disposal

Section 6).

9) During recharge, make sure cords are protected from damage.

10) Do not crush, cut, pull or expose recharge adapter cords to extreme heat.
11) Position recharge cords away from sharp edges so they do not become a safety

hazard by becoming entangled.

NOTE:

THIS UNIT IS SHIPPED IN A PARTIALLY CHARGED STATE.

UPON RECEIPT, IMMEDIATELY CHARGE THE BATTERY FOR

18 - 20 HOURS, USING AC CHARGER.
RECHARGE AFTER EACH USE.

Содержание VEC142

Страница 1: ...ble design The repaired or replaced unit will then be warranted under the terms of the remainder of the warranty period The customer is responsible for the shipping charges on all returned items after 30 days During the warranty period Vector Manufacturing Ltd will be responsible for the return shipping charges LIMITATIONS This warranty does not cover accessories bulbs fuses and batteries defects ...

Страница 2: ... locked position simply rotate the thumbscrew counter clockwise to loosen Then position the swivel head in the desired position and tighten the thumbscrew to hold in place An additional benefit of the WorkLight is the utility value of the clamp and hook accessory Utilizing this accessory provides many mounting positioning options that can allow for hands free operation 2 1 IMPORTANT SAFETY INFORMA...

Страница 3: ...er switch 1 The trigger switch is located on the front of the pistol grip handle of the spotlight see Figure 1 2 To turn the Xtreme Sport Spot 2 000 000 On squeeze the trigger switch 3 To turn the Xtreme Sport Spot 2 000 000 Off release the trigger switch 4 To lock the trigger switch into the on position for continuous operation squeeze the trigger switch and firmly press the trigger locking butto...

Страница 4: ...ger switch is turned Off 3 Lift the battery pack cover and remove it 4 Carefully disconnect the positive and negative wires from the battery clips noting the position of the wires 5 Follow the directions to replace the quartz halogen bulb in the spotlight to gain access to the battery from the inside of the spotlight body 6 Push on the battery from the inside of the body to remove the battery 7 Se...

Отзывы: