4
6.
CLIP-ON LENSES
Use the safety/warning signal amber and red lenses as a filter for the Xtreme Sport
Spot
®
2,000,000.
INSTALLING THE AMBER AND RED LENSES
1. Remove the black rubber bezel
2. Securely clip colored lens filter over spotlight
3. To remove filter, gently pull tabs on both sides of the lens and replace rubber bezel
7.
BULB REPLACEMENT
For bulb replacement you will need a small Phillips-head screwdriver. To replace the
H3 12 volt Halogen Spotlight Bulb (see Figure 4A and Figure 4B):
1.
Disconnect the Xtreme Sport Spot
®
2,000,000 from any charging/power source.
2.
Remove the battery cover (see battery replacement section 7 figure 5 for directions).
3.
Disconnect one wire from a battery terminal.
4.
Remove the rubber bezel by pulling it away from the spotlight lens.
5.
Remove the two Phillips-head screws that hold the retaining ring to the spotlight
body.
6.
Pull off the retaining ring and set it aside.
7. Carefully remove the glass lens, rubber “O” ring and reflector assembly.
8.
Loosen (no need to fully remove) the Phillips-head screw in the neck of the reflector
assembly - this will release the bulb unit.
9.
Disconnect the bulb’s center conductor wire from it’s connecting wire.
10.
Gently pull out the bulb unit and replace with a new H3 12 volt halogen bulb from
Vector (or minimum H3 12V 55W), available from an electrical supply house or
from Vector’s technical support department, call (954) 584-4446.
11.
Reverse the above procedure to re-assemble the spotlight.
FIGURE 4A
3
FIGURE 1
FIGURE 2
The Xtreme Sport Spot
®
can be operated with or without the battery installed.
Operation from external 12 volt DC source with at least 10 amps capacity will
allow lamp operation and internal battery charge.
SPOTLIGHT
– Using the locking trigger switch:
1. The trigger switch is located on the front of the pistol-grip handle of the
spotlight (see Figure 1)
2. To turn the Xtreme Sport Spot
®
2,000,000 On, squeeze the trigger switch
3. To turn the Xtreme Sport Spot
®
2,000,000 Off, release the trigger switch
4. To lock the trigger switch into the on position for continuous operation, squeeze
the trigger switch and firmly press the trigger locking button located on the side
on the handle (see Figure 1); the spotlight will stay on until the lock is released
AREA UTILITY LIGHT
1. Will provide 18 hours of continuous utility lighting - THE AREA-UTILITY LIGHT is
ideal for roadside repairs, as a flashlight, for work areas, for use as a campsite
area light, for power outage, etc
2. The On/Off button for the area light is located near the bottom of the handle, on
the left side (see Figure 1 & 3)
3. To turn the area light On, press the button
4. To turn the area light Off, press the button
5.
HANDS-FREE OPERATION
USING THE BUILT-IN HANGING HOOK:
1. Unsnap the workstand legs from over the hanging hook and spread them apart
so you can lift the hook into the upright position (see Figure 3)
2. Return the stand legs to the storage bracket
3. Use the hook to position the spotlight in any safe, convenient location for
hands-free use
4. For hand-held use: Open the stand legs, fold the hook down, and snap the legs
back into the storage bracket
USING THE BUILT-IN STAND:
1. Unsnap the leg stands from over the hanging hook and spread them apart so you
can lift the hook into the upright position (see Figure 3) (do not over extend)
2. Push the legs towards the front of the spotlight and the hook towards the back,
creating a tripod
3. Turn the spotlight upside-down,
and rest it on the stand (see Figure 3)
4. The spotlight and/or area utility light
may now be used hands-free
5. For hand-held operation, simply
fold the hook down and snap
the legs back into the storage bracket
FIGURE 3 -
XTREME SPORT SPOT
®
BUILT-IN STAND