VAT 14036-E01 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 43

VAT 14036-E01 Скачать руководство пользователя страница 22

MAINTENANCE

Series 140

22/43

Edition 14.07.2020

875067EA

7

Maintenance

WARNING

Unqualified personnel

Inappropriate handling may cause serious injury or property damage.

Only qualified personnel are allowed to carry out the described work.

WARNING

Heavy weight

Physical overstraining.

Use a crane to lift the product.

WARNING

Hazardous components

Human body parts may get jammed and severely injured.

Before starting maintenance:
– disconnect compressed air supply
– disconnect electrical power supply

WARNING

Movable parts

Human body parts may get jammed and severely injured.

Keep human body parts away from movable parts.

7.1

Maintenance intervals

Under clean operating conditions the valve does not require any maintenance during
200 000 cycles (DN400: after 200 000 cycles in horizontal mounting position, after 50 000
cycles in vertical mounting position). After 200 000 cycles, VAT recommends to replace the
valve gate; see chapter «7.3 Removing valve gate».

For more information or a general overhaul please contact one of our service centers.
You will find the addresses on our website www.vatvalve.com.

«
...
20
21
22
23
24
...
»

Содержание 14036-E01












































Отзывы:

Нет отзывов