VAT 14036-E01 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 43

VAT 14036-E01 Скачать руководство пользователя страница 16

OPERATION

Series 140

16/43

Edition 14.07.2020

875067EA

5

Operation

WARNING

Unqualified personnel

Inappropriate handling may cause serious injury or property damage.

Only qualified personnel are allowed to carry out the described work.

WARNING

Movable parts

Human body parts may get jammed and severely injured.

Do not operate before product is installed completely into the vacuum system.

5.1

Normal operation

5.1.1

Manually actuated

Valve is opened and closed manually by a lever or hand wheel.

5.1.1.1

Lever actuated

1. Pull out and hold locking bolt.

2. To open valve, rotate lever counter-clockwise.

3. To close valve, rotate lever clockwise.

The lever is fixed in position “open” and “closed” by the locking bolt.

5.1.1.2

Hand wheel actuated

1. To open valve, rotate hand wheel counter-clockwise.

2. To close valve, rotate hand wheel clockwise

The actual valve position is indicated at the position indicator.

«
...
14
15
16
17
18
...
»

Содержание 14036-E01












































Отзывы:

Нет отзывов