Vascat MAC-HS 100 Скачать руководство пользователя страница 34

Страница: 34 / 64

OPERATION AND MAINTENANCE MANUAL

MAC-HS MOTORS

PAGE: 34

CODE: CTT32 EDITION: 04 RELEASE: SEPTEMBER 2020

Subject to technical changes without prior notice

3.8.4

Provision for accelerometer assembly

As an option and according to the customer's specifications, motors in the MAC-HS series can be adapted for accelerometer

assembly. This type of sensor provides information about the vibrations in the motor. Accelerometers can be fitted at different
places on the motor according to each customer's requirements. The following figure shows one possible setup:

Figure 8: Accelerometer provision

3.8.5

Noise level

The technical data sheets VASCAT provides for each motor show the noise level in dB issued by each model.

Optionally, motors can be fitted with a kit to reduce the level of noise emissions. Please check with VASCAT for more details.

The machines directive specifies a noise level of 80 dB at work posts. The user is responsible for guaranteeing said level using

the installation of external absorption devices if necessary.

Tapped holes for

accelerometers

Содержание MAC-HS 100

































































Результаты поиска

Содержание MAC-HS 100

Отзывы:

Похожие инструкции для MAC-HS 100

Бренды по названию

Популярные бренды

Vascat MAC-HS 100, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MAC-HS 100

Отзывы:

Похожие инструкции для MAC-HS 100

Бренды по названию

Популярные бренды