Vascat MAC-HS 100 Скачать руководство пользователя страница 24

Страница: 24 / 64

OPERATION AND MAINTENANCE MANUAL

MAC-HS MOTORS

PAGE: 24

CODE: CTT32 EDITION: 04 RELEASE: SEPTEMBER 2020

Subject to technical changes without prior notice

3.6

Mechanical specifications

3.6.1

Mounting

Available construction types for MAC HS motors are detailed in the table below:

EN 60034-7

FRAME SIZES

100

132

160

200

250

IM B3

IM 1001

IM B3/B5

IM 2001

IM V1 / V3

IM 3011 / IM 3031

optional

IM V5 / V6

IM 1011 / IM 1031

optional

IM V18 / V19

IM 3611 / IM 3631

optional

Table 15 Available construction types for MAC-HS motors

Other assembly types, such as ‘trunnion’ (double flange), available on request.

3.6.2

IP protection rating

MAC-HS series motors are defined with the following IP degrees:

Motor

Standard

version

Optional

ratings

MAC-HS

IP23

IP54

Table 16: Protection rating of MAC-HS motors

The motors defined as IP23 must take some precautions if they are installed in environments that are dusty, damp or subject to

adverse weather.

Содержание MAC-HS 100

































































Результаты поиска

Содержание MAC-HS 100

Отзывы:

Похожие инструкции для MAC-HS 100

Бренды по названию

Популярные бренды

Vascat MAC-HS 100, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MAC-HS 100

Отзывы:

Похожие инструкции для MAC-HS 100

Бренды по названию

Популярные бренды