Varian 960 Скачать руководство пользователя страница 108

Страница: 108 / 230

Models 947, 948 and 960 Leak Detectors Operations and Service Manual

3-34

7. Press and hold the

VENT

button for approximately 1 second until the unit switches to

the VENT mode.

❑

The TEST LED turns off.

❑

The VENT LED illuminates.

NOTE

If the VENT button is pressed for less than one second, the leak
detector moves to HOLD.

8. Remove the tested part from the test port.

The Leak test is now complete.

3.15 Standby

When continued use of 947/948/960 is not anticipated, STANDBY

mode, a partial

shutdown, can be used to save energy. To put the 947/948/960 into STANDBY

mode:

1. Press the

VENT

button and hold it until the Vent LED comes on.

2. Place the Rough pump power switch in the

OFF

position.

3. Turn the Rough pump switch breaker to the

position to return the Leak Detector to

the READY FOR OPERATION mode.

NOTE

When the unit is returned to Ready for Operation from Standby,
the warmup periods do not apply.

3.16 Shutdown

Complete shutdown for a move or temporary storage is accomplished by the following
shutdown procedure:

1. Place the test port plug securely in the test port.

2. Turn the ROUGH PUMP switch

OFF

3. Turn DETECTOR switch

OFF

4. Turn the Power switch/circuit breaker

OFF

on back of cabinet.

5. For the 948/960 only, empty the cold trap.

See “Liquid Nitrogen Cold Trap (Models 948/960 only)” on page 4-11 for the cleaning
procedure.

Содержание 960







































































































































































































































Результаты поиска

Содержание 960

Отзывы:

Похожие инструкции для 960

Бренды по названию

Популярные бренды

Varian 960, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 960

Отзывы:

Похожие инструкции для 960

Бренды по названию

Популярные бренды