background image

VLC5501 User manual

7

PIN codes:

PIN codes:

  The Vapormatic keypad can store up to 5 User codes and one Master code, the Master

code is used to add and delete your five user codes. Therefore a secondary user should be given one of
the five possible User codes, which they can not modify add or delete other codes with.  Only the
Master code can do this, in the event of a Master code being lost or forgotten, please refer to the PIN
code card also supplied with this system.

All PIN codes can be 4 to 8 digits long; the PIN code entry is confirmed with the

#

 key.

Example:

Factory default is ‘0000’ then press the

#

to confirm, you will hear two short beeps

and the green LED light will illuminate.  If the incorrect code has been entered the
keypad will emit one long beep, the keypad will then lock out.  In this instance,
please switch the ignition off and then back on again, this will reset the keypad ready
for a correct code to be entered.

Attention!!”

Factory default code should be changed at time of installation, please refer to

master code setting later in this manual.

Code definitions:

Master PIN code:

The Vapormatic keypad comes supplied with a factory default PIN
code of ‘0000’. It is

important

  to  change  this  to  a  new  4  to  8  digit

unique Master PIN code that only the owner should know. The Master
PIN code is used to add and delete up to 5 additional user codes.

User PIN code:

With the use of the Master PIN code, an additional five access codes
can be added for non owner driver authorisation. Any of these can be
deleted or changed at any time.  A user code does not have access to
add or delete any authorisation codes.

Override PIN code

:

In the event of the Master PIN code being lost or forgotten, the unique 8
digit Override code should be used to reset the security system.  After
the Override code has been entered, the security system will delete all
PIN codes from memory, and the Master PIN code will be reset to the
factory default code of ‘0000’.

Note:

 The Override code can be found on the PIN code card, by scratching off protection layer

(see

PIN code card

).

Additional users chart:

If more than one user has access to this vehicle, additional PIN codes can be stored. A total of five
additional user PIN codes (except master PIN code) can be stored in the system’s memory (see table)

Keypad memory slot

User

Customer codes

0

Master pin code

1

PIN code for User1

2

PIN code for User2

3

PIN code for User3

4

PIN code for User4

5

PIN code for User5

Содержание VLC5501



















Отзывы: