Vapormatic VLC5501 Скачать руководство пользователя страница 11

VLC5501 User manual

11

System status indication:

It is possible to detect the system status, using the keypad LED’s (see table):

Operation

Red LED

Green LED

Backlight

Ignition switched OFF

OFF

OFF

OFF

Ignition switched ON, PIN code not entered
(system armed)

ON

OFF

ON for 30
seconds, then
OFF

Ignition switched ON, Master PIN code entered (system disarmed) 

OFF

ON

ON for 5
seconds, then
OFF

Ignition switched ON, user PIN code entered (system disarmed)

OFF

ON

OFF

Also there are sound notifications used to show the security system status (see table):

Operation

Sound signal

System ready (after ignition switched ON)

1 short beep

Pressing any soft key

1 short beep

Confirming correct PIN code

2 short beeps

Confirming incorrect PIN code

1 long beep

Confirming correct Overriding PIN code

6 short beeps

Confirming incorrect Overriding PIN code

1 long beep

Low battery warning for Keypad Override Disc

4 short beeps

Ordering replacement parts:

Vapormatic can supply replacement keypads and Keypad Override disc’s the part numbers are listed
below.

PLEASE NOTE

:  These products have to be coded to the serial number of your security system.

Please quote the serial number listed on the PIN code card as described earlier, please allow up to
fourteen working days when ordering.

VLC5504 - Keypad
VLC5507 - Keypad Override Disc

Содержание VLC5501



















Отзывы: