WORK AREA
1.
Keep your work area clean and well lit.
Cluttered benches and dark areas invite accidents.
2.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust.
Power tools create sparks which may ignite the dust or fumes.
3.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can
cause you to lose control.
ELECTRICAL SAFETY
1. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change
the plug in any way. Double insulation eliminates the need for the three wire grounded power cord
and grounded power supply system.
2.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your body is grounded.
3.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase
the risk of electric shock.
4.
Do not abuse the cord. Never use the cord to carry the tool or pull the plug from an outlet.
Keep cord away from heat, oil, sharp edges or moving parts.
Replace damaged cords
immediately. Damaged cords increase the risk of electric shock.
5. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These
cords are rated for outdoor use and reduce the risk of electric shock.
EXTENSION CORD SELECTION
Replace damaged extension cords immediately. Use of damaged extension cords can shock,
burn or electrocute. If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible motor damage. A table
of recommended extension cord sizes will be found in this section. This table is based on limiting
line voltage drop to 5 volts for 115 volts at 150% of rated amperes. If an extension cord is to be used
outdoors it must be marked with the suffix W-A or W following the cord type designation. For example
– SJTW-A to indicate it is acceptable for outdoor use.
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS:
Length of Cord in Feet
115V
25 ft. 50 ft. 100 ft. 150 ft. 200 ft. 250 ft. 300 ft. 400 ft. 500 ft.
0-2A
18
18
18
16
16
14
14
12
12
2-3A
18
18
16
14
14
12
12
10
10
3-4A
18
18
16
14
12
12
10
10
8
4-5A
18
18
14
12
12
10
10
8
8
5-6A
18
16
14
12
10
10
8
8
6
6-8A
18
16
12
10
10
8
6
6
6
8-10A
18
14
12
10
8
8
6
6
4
10-12A
16
14
10
8
8
6
6
4
4
12-14A
16
12
10
8
6
6
6
4
2
14-16A
16
12
10
8
6
6
4
4
2
16-18A
14
12
8
8
6
4
4
2
2
18-20A
14
12
8
6
6
4
4
2
2
PERSONAL SAFETY
1.
Stay alert, watch what you are doing, and use common sense when operating a power
tool.
Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in serious personal injury.
2.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught in
moving parts.
3.
Avoid accidental starting. Be sure switch is OFF before plugging in.
Carrying tools with your
finger on the switch or plugging in tools that have the switch ON invites accidents.
4.
Remove adjusting keys or wrenches before turning the tool ON.
A wrench or a key that is left
attached to a rotating part of the tool may result in personal injury.
5.
Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance
enable better control of the tool in unexpected situations.
6.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard
hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
1.
Use clamps or other practical means to secure and support the workpiece to a stable
platform.
Holding the work by hand or against your body is unstable and may lead to loss of control.
2.
Do not force tool. Use the correct tool for your application.
The correct tool will do the job
better and safer at the rate for which it is designed.
3.
Do not use tool if switch does not turn it ON or OFF.
A tool that cannot be controlled with the
switch is dangerous and must be repaired.
4.
Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool.
Such preventive safety measures reduce the risk of starting the
tool accidentally.
5.
Store idle tools out of reach of children and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
6.
Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using.
Many accidents are caused by poorly maintained tools.
7.
Use the power tool, accessories and tool bits etc., in accordance with these instructions
and in the manner intended for the particular type of power tool, taking into account the
working conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous situation.
4
5
