Vanguard Amity SCIVFB Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 32

background image

22

104025

CLEANING

AND

MAINTENANCE

WARNING ICON

G 001

WARNING

Turn off heater and let cool before cleaning.

WARNING ICON

G 001

CAUTION

You must keep control areas, burner, and circulating air passage-
ways of heater clean. Inspect these areas of heater before each
use. Have heater inspected yearly by a qualified service person.
Heater may need more frequent cleaning due to excessive lint from
carpeting, bedding material, etc.

TROUBLE-

SHOOTING

Note: All troubleshooting

items are listed in order of

operation.

WARNING ICON

G 001

WARNING

Turn off and unplug heater and let cool before servicing. Only a
qualified service person should service and repair heater.

WARNING ICON

G 001

CAUTION

Never use a wire, needle, or similar object to clean ODS/pilot. This
can damage ODS/pilot unit.

POSSIBLE
CAUSE

1. Ignitor electrode not

connected to ignitor cable

2. Ignitor cable pinched or

wet

3. Piezo ignitor nut is loose

4. Broken ignitor cable
5. Bad piezo ignitor
6. Ignitor electrode posi-

tioned wrong

7. Ignitor electrode broken

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if

pinched by any metal or
tubing. Keep ignitor
cable dry

3. Tighten nut holding

piezo ignitor to base
panel of log set. Nut is
located behind base
panel.

4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace ignitor

7. Replace ignitor

OBSERVED
PROBLEM

When ignitor button
is pressed, there is no
spark at ODS/pilot

ODS/PILOT AND BURNER

• Use a vacuum cleaner or small, soft bristled brush to clean.

LOGS

• Replace log(s) if broken or chipped (dime-sized or larger).

«
...
20
21
22
23
24
...
»

Содержание Amity SCIVFB

































Отзывы:

Нет отзывов

Похожие инструкции для Amity SCIVFB

Бренд: Aarrow Страницы: 36

Бренд: RAIS Страницы: 339

Бренд: Zibro Страницы: 12

Бренд: Warmington Страницы: 12

AVALON 4 Series

Бренд: Hunter Stoves Страницы: 28

Бренд: Ravelli Страницы: 12

Бренд: HAMPTON BAY Страницы: 36

JAZZ Hydromatic 30 Acs H1

Бренд: MCZ Страницы: 44

Бренд: Ecotec Страницы: 37

Бренд: Cola Страницы: 14

Ellis Cook Stove BCS01

Бренд: Boru Stoves Страницы: 32

Бренд: Procom Страницы: 28

Бренд: Electralog Страницы: 9

Бренд: Costway Страницы: 11

Бренд: HWAM Страницы: 56

Autopilot IHS 3120

Бренд: HWAM Страницы: 60

Eta Express 3530

Бренд: Primus Страницы: 8

Бренд: Primus Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды