Vanguard Amity SCIVFB Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 32

background image

8

104025

WARNING ICON

G 001

WARNING

Never install the heater

• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture, clothing, or other flammable objects are

less than 36 inches from the front, top, or sides of the heater

• in high traffic areas
• in windy or drafty areas

INSTALLING

NOTICE

A qualified service person must install heater. Follow all local codes.

WARNING ICON

G 001

CAUTION

This heater creates warm air currents. These currents move heat
to wall surfaces next to heater. Installing heater next to vinyl or
cloth wall coverings or operating heater where impurities in the air
(such as tobacco smoke) exist, may discolor walls.

CHECK GAS TYPE

Use only propane gas. If your gas supply is not propane, do not install heater. Call
dealer where you bought heater for proper type heater.

IMPORTANT:

Vent-free heaters add moisture to the air. Although this is benefi-

cial, installing heater in rooms without enough ventilation air may cause mildew
to form from too much moisture. See Air for Combustion and Ventilation, pages 5
through 7.

NOTICE

State or local codes may only allow operation of this appliance in a
vented configuration. Check your state or local codes.

CLEARANCES TO COMBUSTIBLES (Vent-Free Operation Only)

WARNING ICON

G 001

WARNING

Maintain the minimum clearances. If you can, provide greater clear-
ances from floor, ceiling, and adjoining side and back walls.

Carefully follow the instructions below. This stove is a freestanding unit designed
to set directly on the floor.

IMPORTANT:

You must maintain minimum wall and

ceiling clearances during installation. The minimum clearances are shown in
Figure 4, page 9. Measure from outermost point of stove top.

Minimum Wall and Ceiling Clearances (see Figure 4)

A. Clearances from outermost point of stove top to any combustible side wall

should not be less than 12 inches.

B. Clearances from outermost point of stove top to any combustible back wall

should not be less than 6 inches (Includes Corner Installations).

C. Clearances from the stove top to the ceiling should not be less than 48 inches.

«
...
6
7
8
9
10
...
»

Содержание Amity SCIVFB

































Отзывы:

Нет отзывов

Похожие инструкции для Amity SCIVFB

Бренд: Horus Страницы: 109

MIRAGE 30 SERIES A

Бренд: Pacific energy Страницы: 36

Бренд: Piazzetta Страницы: 52

Бренд: Olimpia splendid Страницы: 8

Бренд: Avalon Страницы: 34

Бренд: Valor Страницы: 61

Бренд: Arada Страницы: 32

Бренд: Hegrom Страницы: 9

Бренд: Silvercrest Страницы: 25

Бренд: Silvercrest Страницы: 118

Бренд: Heartland Appliances Страницы: 37

Бренд: HWAM Страницы: 12

Бренд: HWAM Страницы: 12

Бренд: Xtreme Power Страницы: 2

Бренд: Charnwood Страницы: 17

Бренд: Charnwood Страницы: 20

Бренд: Charnwood Страницы: 24

Бренд: Charnwood Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды