Vanguard Amity SCIVFB Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 32

background image

26

104025

TECHNICAL

SERVICE

You may have further questions about installation, operation, or troubleshooting.
If so, contact DESA International’s Technical Service Department at
1-800-DESA LOG (1-800-337-2564).

When gas pressure is too low

• pilot will not stay lit
• burners will have delayed ignition
• heater will not produce specified heat
• Propane/LP gas supply may be low

When gas quality is bad

• pilot will not stay lit
• burners will produce flames and soot
• heater will backfire when lit

You may feel your gas pressure is too low or gas quality is bad. If so, contact your
local propane/LP gas supplier.

SERVICE

HINTS

Note:

Use only original replacement parts. This will protect your warranty cover-

age for parts replaced under warranty.

Parts Under Warranty

Contact authorized dealers of this product. If they can’t supply original replace-
ment part(s), call DESA International’s Technical Service Department at
1-800-323-5190. When calling DESA International, have ready

• your name and address
• model number of your heater
• how heater was malfunctioning
• type of gas used (propane or natural gas)
• purchase date

Usually, we will ask you to return the defective part to the factory.

Parts Not Under Warranty

Contact authorized dealers of this product. If they can’t supply original replace-
ment part(s), call DESA International’s Parts Department at 1-800-972-7879 for
referral information. When calling DESA International, have ready

• model number of your heater
• the replacement part number

REPLACEMENT

PARTS

SPECIFICATIONS

Amity



Stove Gas Log Heater

Model SVYD18P
Variable Manually Controlled

Btu (Variable)

16,000/30,000

Type Gas

Propane Only

Ignition

Piezo

Pressure Manifold

8.0" W.C.

Inlet Gas Pressure (in. of water)

Maximum

14"

Minimum*

11"

* For input adjustment

Shipping Weight

28 lbs.

Amity



Stove Cabinet

Model SCIVF(*)

Shipping Weight

195 lbs.

(* Indicates Color Suffix Designation)

«
...
24
25
26
27
28
...
»

Содержание Amity SCIVFB

































Отзывы:

Нет отзывов

Похожие инструкции для Amity SCIVFB

Бренд: Cadel Страницы: 200

Fiorina 103 S-line

Бренд: Zibro Страницы: 126

Bear IT 10+5 kW

Бренд: Koper Страницы: 36

Бренд: Accont Страницы: 32

Бренд: Kalor Страницы: 29

Бренд: Harman Страницы: 36

Triton 450 Glass

Бренд: Capital fireplaces Страницы: 8

Бренд: Heartland Страницы: 64

Бренд: Coleman Страницы: 2

Бренд: Coleman Страницы: 4

Бренд: Coleman Страницы: 18

Бренд: Coleman Страницы: 24

Бренд: Heartland Страницы: 75

Бренд: NorthStar Страницы: 16

Бренд: Brixton Страницы: 56

Бренд: Baxi Fires Division Страницы: 7

Бренд: Royal Страницы: 24

Бренд: Palazzetti Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды