manualshive.com logo in svg

Vanguard Instruments Company CT-6500, Руководство по эксплуатации

Поделиться
Скачать
Vanguard Instruments Company CT-6500 Скачать руководство пользователя страница 29

CT-6500 Operating Instructions

22

Table 6.0  Close-Open Operation Using Contact Channel #1

STEP

OPERATION

ACTION

DISPLAY

1

READY TIMER FOR BREAKER OPERATION.

PRESS #1 KEY.

INSERTION RESISTOR?

1.NO

2.YES

2

SELECT NO INSERTION RESISTOR.

PRESS #1 KEY.

TIMING WINDOWS:

1.WINDOW = 1  SEC

2.WINDOW = 10 SEC

3.WINDOW = 20 SEC

3

SELECT 1-SECOND WINDOW.

PRESS #1 KEY.

TRIGGER MODE:

1.Internal Trigger

2.External Trigger

4

SELECT INTERNAL TRIGGER.

PRESS #1 KEY.

TIMING MODE:

1. OPEN

2. CLOSE

3. O-C

4. C-0

5. O-C-O

5

SELECT CLOSE-OPEN OPERATION.

PRESS #4 KEY.

C-O Second Trigger:

1. Contact #1 CLOSE

2. Set DELAY

3. No DELAY

6

SELECT CONTACT #1 CLOSE.

PRESS #1 KEY.

CLOSE-OPEN TIMING

Hold "ARM" Switch,

Then "START".

"STOP" to ABORT

7

INITIATE OPEN COMMAND.

HOLD THE "ARM"

SWITCH AND

PRESS THE "START"

KEY.

TEST IN PROGRESS

Hold "ARM"  Until

Test complete.

(Up to 15 seconds)

8

ANALYZER IS READY TO OUTPUT RESULTS.

NONE.

1.TIME BREAKER

2.GET RESULT

3.SET-UP

4.DIAGNOSTIC

NOTE

1. Users can program a delay from 10 to 500 ms between the CLOSE and
OPEN commands. When a delay is used in the operation, it may not
represent a true breaker operating condition.

2. Users can also program in no delay for the operation in which case, the
CLOSE and OPEN commands are initiated at the same time by the CT-
6500.

Содержание CT-6500






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды