Vanguard Instruments Company CT-6500 Скачать руководство пользователя страница 17

Страница: 17 / 69

CT-6500 Operating Instructions

7.5 CT-6500 Printer Paper Control

To advance the paper from the printer, press and release the “

↑

PAPER LCD” button. To

retract the thermal paper from the printer, press and release the “

↓

PAPER LCD” button.

7.6 Replacing CT-6500 Thermal Paper

The roll of thermal paper resides inside a pocket underneath the printer cover. To replace the

paper, follow the steps below:

Remove the printer cover.

Remove the leftover thermal paper roll from the paper holder.

Unroll the new thermal paper.

Feed the thermal paper into the slot between the paper pocket and the rubber

roller. The printer will automatically pull the paper under the thermal head.

Place the paper roll into the paper holder.

Lift the thermal head and align the thermal paper if necessary.

Replace the printer cover back.

NOTE

The thermal paper will show a red stripe in the margin to indicate that the roll is
about to run out of paper.

7.7 CT-6500 LCD Contrast Control

To darken the LCD screen, press and hold the “

↑

PAPER LCD” button, while to decrease the

contrast of the LCD screen, press and hold the “

↓

PAPER LCD” until the desired contrast is

reached.

Содержание CT-6500






































































Результаты поиска

Содержание CT-6500

Отзывы:

Бренды по названию

Популярные бренды

Vanguard Instruments Company CT-6500, Руководство по эксплуатации

Результаты поиска

Содержание CT-6500

Отзывы:

Бренды по названию

Популярные бренды