background image

     

Service and Installation Manual

 

5                                   

For  warranty  service,  call  1-888-VALPRO8  /  1-813-502-030                 

                       

 

 

Technical Information   

Model 

VPIM-55 

VPIM85 

VPIM280 

Electrical input 

115VAC ~ 60Hz 

115VAC ~ 60Hz 

115VAC ~ 60Hz 

Power consumption 

11.3 kW

·

h /100 lbs of 

ice 

10.8 kW

·

h /100 lbs of 

ice 

7.2 kW

·

h /100 lbs of 
ice 

Ice-making rated current 

2.2A 

4.7A 

9.6A 

Ice-harvest rated current 

2.2A 

8.4A 

14.2A 

Refrigerant 

R134a, 8.1 oz. 

R134a, 6.0 oz. 

R404A, 22.2 oz. 

High Side Pressure 

190psig 

210psig 

455psig 

Low Side Pressure 

90psig 

90psig 

200psig 

Width x Depth x Height 

19 11/16" x 17 23/32" 

x 31 1/2" 

19 11/16" x 22 1/16" x 

31 1/2" 

26" x 26 3/8" x 38 

1/4"(Max. 39 1/2") 

Unit weight 

70.5 lbs 

88.2 lbs 

121.3 lbs 

Ice storage capacity 

25 lbs 

30 lbs 

80 lbs 

Ice-making capability 

55 lbs/day* 

85 lbs/day* 

280 lbs/day* 

*The actual quantity of ice produced per day can vary with room and water 
conditions. 
The technical data and performance index listed above should be used for 
reference only. They are subject to change. 
This product has been tested and certified to NSF standard 12 by INTERTEK.

 

Introduction

 

The IM Series of Ice Cube Machine finds wide application in households, bars, 
restaurants, hotels, supermarkets, etc. These units produce crystal-clear, 
gourmet cube ice, and offer convenience for homeowners and hotel guests. An 
insulated ice storage bin is built into each ice cube machine.   

This user’s manual is intended as a resource for persons installing, using and 
servicing model VPIM-55,VPIM-85, VPIM-280. It contains valuable 
information on safety and maintenance. We strongly recommends that this 
manual be kept in a place where it can be accessed when needed.   

This Ice Cube Machine is designed and manufactured according to the highest 
standards of safety and performance. It meets or exceeds the safety standard of 
UL563 and sanitation standard NSF12. 

We assumes no liability or responsibility of any kind for products 
manufactured that have been altered in any way, including the use of any parts 
and/or other components not specifically approved by us. We reserves the right 
to make design changes and/or improvements at any time. Specifications and 
designs are subject to change without notice.

 

   

Service and Installation Manual   

 

 

 

             

For warranty service, call 1-888-VALPRO8 / 1-813-502-030                         

         

22

Ice-Making System Cleaning 

Minerals that are removed from water during the freezing cycle will eventually 
form a hard, scaly deposit in the water system. Cleaning the system regularly 
helps remove the mineral scale buildup. How often you need to clean the 
system depends on how hard your water is or how effective your filtration may 
be. With hard water of 15 to 20 grains/ gallon (4 to 5 grains/liter), you may 
need to clean the system as often as every 3 months. 

1.

 

Press the STANDBY button to switch it off. 

2.

 

Remove all ice cubes from the storage bin. 

3.

 

Make sure the unit stop working. (the drain pump stop and standby LED is 
on green) Pour 8 oz. of Nickel-Safe Ice Maker Cleaner Solution into the 
water tank.   

4.

 

Keep the ice maker connected to the water supply.   

5.

 

Keep the ice maker is plugged in. Press the CLEAN button. The machine 
will run the Automatic Clean mode. The green clean cycle LED will be on. 

6.

 

The first clean cycle will continue for 30 minutes unless you press the 
STANDBY button (you can press the STANDBY button to stop the clean 
cycle any time during the clean cycle). After 30 minutes, the drain pump 
work, the water in the water tank and the water line will be drain out.   

7.

 

The water inlet valve work and the water enter the water tank. The second 
clean cycle begins. Repeat step 6 above two times to rinse the ice-making 
system completely. 

NOTE: Do not add Ice Maker Cleaner Solution to the water trough during 
the last two rinses. 

8.

 

After cleaning, the machine returns to Stand-by mode and green standby 
LED light. Others LEDs will be off (Except the cleaning recommended 
indicator light). 

9.

 

Prepare a sanitizing solution made of 1 ounce of household bleach and 2 
gallons of hot water (95º to 115ºF). Wipe the entire bin inside and outside, 
covering the entire body surface. 

10.

 

Fill a spray bottle with the sanitizing solution and spray all corners and 
edges, making sure to cover all surfaces with the solution. 

11.

 

Allow the solution to be in contact for at least 3 minutes, then dry. 

12.

 

Repeat step 6 above to rinse the ice making system one more time.   
NOTE: Do not add Ice Maker Cleaner Solution to the water trough during 
rinsing stage. 

13.

 

After cleaning, the machine returns to Stand-by mode and red standby LED 

Содержание VPIM55

















Отзывы: