Service and Installation Manual
25
For warranty service, call 1-888-VALPRO8 / 1-813-502-030
on. If you want to restart the ice-making process after cleaning, press the
ICE button directly more than 3 seconds and the ice machine will
automatically go into the ice-making process.
6.
If you want to interrupt the cleaning mode before it is finished, do not press
the CLEAN button again. Instead, press the STANDBY button more than 3
seconds, this will stop the cleaning mode.
7.
If you want to adjustment the size of individual ice cubes, make sure ice
machine is in Stand-by mode, you can press the STANDBY button more
than 5 seconds to enter adjustment stage, then through press ICE button to
increase the thickness of ice cubes, and press CLEAN button to decrease the
thickness of ice cubes. When you press ICE or CLEAN button one time, the
thickness of ice cubes will increase or decrease 5%, and the most you can
press ICE or CLEAN button is 10 times.
When the adjustment is done, you should press STANDBY button to
confirm the adjustment.
8.
If the machine is on but the Ice Making
，
Ice Harvest and Bin Full three
indicator lights is blinking, which indicate that there is not enough water in
the system. Firstly check if you turn on water supply tap or not, then check
the pressure of water supply, etc.
Descriptions of LEDs and buttons:
1.
Standby (Red) LED:
Stand-by indicator light
When this LED is on, the ice machine is in Stand-by mode. The unit doesn’t
work, and the red LED will be on. When this LED is flashing shows that the
drain pump is working. After the water in the water tank drain out, the unit
will return to the Stand-by mode.
2.
Ice Making (Green) LED:
Ice Making indicator light
When this LED is on, the unit is working in the ice-making mode.
3.
Ice Harvest (Yellow) LED:
Ice Harvest indicator light
When this LED is on, the unit is working in the ice harvest mode controlled
by the ice slide way.
4.
Bin Full (Red) LED:
Ice Full indicator light
When this LED is on, the ice storage bin is full of ice cubes or there is
something obstructing the ice slide way. The unit will stop working. When
ice cubes are removed from the ice storage bin, clearing the ice slide way,
the unit will restart and return to the ice-making mode.
5.
Clean Cycle (Green) LED:
Clean Cycle indicator light
Service and Installation Manual
For warranty service, call 1-888-VALPRO8 / 1-813-502-030
2
IMPORTANT SAFEGUARDS
Before the ice maker is used, it must be properly positioned
and installed as described in this manual, so read the manual
carefully. We strongly recommends that you have a
professional install your new machine. The warranty may be
affected or voided by an incorrect installation. To reduce the
risk of fire, electrical shock or injury when using the ice
maker, follow basic precautions, including the following:
•
Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not
use an adapter, and do not use an extension cord.
•
It is recommended that a separate circuit, serving only your ice maker, be
provided. Use receptacles that cannot be turned off by a switch or pull chain.
•
Do not connect or disconnect the electric plug when your hands are wet.
•
Never unplug the ice maker by pulling on the power cord. Always grip the
plug firmly and pull straight out from the outlet.
•
Never clean ice maker parts with flammable fluids. Do not store or use
gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. The fumes can create a fire hazard or explosion.
•
Before proceeding with cleaning and maintenance operations, make sure the
power line of the unit is disconnected and the water line is shut off.
(EXCEPTION: When cleaning the machine’s ice making and water systems,
see pages 19-23.)
•
Before operating, put all the enclosure panels back into their original places.
•
Do not touch the evaporator with your hand when the machine is operating.
•
Unplug the ice maker or disconnect power before cleaning or servicing.
Failure to do so can result in electrical shock or death.
•
Do not attempt to repair or replace any part of your ice maker unless it is
specifically recommended in this manual. All other servicing should be
referred to a qualified technician.
•
Use two or more people to move and install ice maker. Failure to do so can
result in back or other injury.
•
To ensure proper ventilation for your ice maker, the front of the unit must be
completely unobstructed. Choose a well-ventilated area with temperatures
above 50ºF (10ºC) and below 100ºF (38ºC). This unit MUST be installed in
