background image

     

Service and Installation Manual

 

3                                   

For  warranty  service,  call  1-888-VALPRO8  /  1-813-502-030                 

                       

 

 

an area protected from the elements, such as wind, rain, water spray or drips. 

 

The ice maker should not be located next to ovens, grills or other sources of 
high heat. 

 

The ice maker must be installed with all electrical and water connections in 
accordance with state and local codes. A standard electrical supply (115 VAC 
only, 60 Hz, 15 A), properly grounded in accordance with the National 
Electrical Code and local codes and ordinances, is required. 

 

Do not kink or pinch power supply cord or drain lines between ice maker and 
cabinet. 

 

The fuse (or circuit breaker) size should be 15 amperes. 

 

It is important for the ice maker to be leveled in order to work properly. You 
may need to make several adjustments to level it. 

 

All installations must be in accordance with local plumbing code 
requirements. 

 

Make certain that the hoses are not pinched or kinked or damaged during 
installation. 

 

Check for leaks after connection. 

 

Remove the packing materials and clean the ice maker before using. 

 

Turn on the water supply tap before switching on the ice maker. Never turn 
the water supply tap off when the ice maker is working. 

 

Except to take ice from the unit, keep the door closed in order to reduce ice 
melting and to promote proper ice formation.   

 

Although the unit has been tested at the factory, due to long-term transit and 
storage, the first batch of cubes must be discarded. 

 

Press the STANDBY button to switch off the unit. DO NOT unplug it when 
the unit is on.   

 

If the ice maker will not be used for a long time, before the next use it must 
be thoroughly cleaned. Follow carefully any instructions provided for 
cleaning or use of sanitizing solution. Do not leave any solution inside the ice 
maker after cleaning. 

 

DO NOT touch the condenser fins. The condenser fins are sharp and can be 
easily damaged. 

 

DO NOT use solvent-based cleaning agents or abrasives on the interior. 
These cleaners may transmit taste to the ice cubes, or damage or discolor the 
interior. 

 

The ice machine cleaner contains acids. DO NOT use or mix with any other 
solvent-based cleaner products. Use rubber gloves to protect hands. Carefully 
read the material safety instructions on the container of the ice machine 
cleaner. 

 

Do not use this apparatus for other than its intended purpose.

 

   

Service and Installation Manual   

 

 

 

             

For warranty service, call 1-888-VALPRO8 / 1-813-502-030                         

         

24

Control Panel

 

(located at middle of front bottom louver panel)

 

 

The control panel includes three buttons and six indicator lights.   

IMPORTANT: 

• 

If you use a water filter and have already set the initial data of water filter, 

under any working status, the cleaning recommended indicator light will be 
on. 

• 

If you do not use a water filter, you needn’t set the initial data of water filter, 

and the cleaning recommended indicator light will be off under any working 
status. 

Operation of the control panel: 

1.

 

When the unit is plugged in, the standby indicator light is on. Ice machine is 
in the Stand-by mode. 

2.

 

During the Stand-by mode, press the ICE button more than 3 seconds, all 
indicator lights are on (except cleaning recommended indicator light), water 
enter the water tank. Then ice machine will start to make ice automatically, 
the ice making indicator will be on. 

3.

 

During harvesting, the ice harvest indicator light is on and the ice making 
indicator is off. When the ice storage bin is full, the bin full indicator is on. 

4.

 

If the CLEAN button is pressed during the ice making mode, it will be 
ignored. The ice-making will continue. 

5.

 

When you want to clean the machine, make sure the ice machine is in 
Stand-by mode. Press the CLEAN button more than 3 seconds and the ice 
machine will start the cleaning mode, the clean cycle indicator will be on. 
After 60 minutes, the cleaning mode stops and the standby indicator light is 

Содержание VPIM55

















Отзывы: