Valor 739DVN Скачать руководство пользователя страница 6

6

Safety Information

NOTE: Always allow adequate clearance around air openings into the combustion chamber and 

maintain accessibility clearances for servicing and proper operation.

2.1 General Safety (Home Owner)

Cleaning.

 To clean the appliance, make sure it 

is off and cold. Then remove the logs and use a 
vacuum to clean the burner and air openings in 
the bottom and back of the appliance. Replace the 
logs.

Fire Extinguisher.

 Every home should have at 

least one 

fi

 re extinguisher. An approved Class 

A-B-C extinguisher should be mounted on the wall 
near an exit and close to the appliance, but not so 
close that accessibility to the extinguisher could 
be blocked by a 

fi

 re. Your local Fire Department 

can advise you concerning the most appropriate 
location.

Smoke Detectors & Carbon Monoxide 
Detectors.

 Install at least one smoke detector on 

each 

fl

 oor of your home to ensure your safety. It 

should be located away from the gas appliance 
and close to the sleeping areas. Follow the smoke 
detector manufacturer’s placement installation 
and maintenance instructions. Your local Fire 
Department may provide assistance in selecting 
smoke detectors and carbon monoxide detectors. 
It is strongly recommended, for your family’s 
protection, that a carbon monoxide detector be 
placed in all homes that utilize gas in any form.

2.2 Safety for the Installer

Wear gloves and safety glasses for protection.
Exercise extreme caution when using ladders 
or when on rooftops.
Be aware of electric wiring locations in walls 
and ceilings.
Use a back support when doing any heavy 
lifting.

2.3 Vent Safety

Venting must be installed according to local codes 
and good venting practices.

2.4 Electrical Code

These appliances, when installed, must be 
electrically grounded in accordance with local 
codes or, in the absence of local codes, with the 

National Electrical Code, ANSI/NFPA 70 

or the 

Canadian Electrical Code, CSA C22.1.

3.1 Planning Your Installation

Please note the following key points regarding the 
location of your appliance:

A suf

fi

 cient gas pressure is required to supply the 

unit with a minimum inlet pressure. 
Allow adequate accessibility clearances for 
servicing and proper operation.
Allow adequate clearance to combustibles and 
around air openings for combustion.
A suitable power outlet is required to provide 
power when 

fi

 tted with a fan.

3.2  Listing and Codes

The Valor model 739 is listed and certi

fi

 ed for 

installation in the U.S.A. and Canada under the 
following standards:

ANSI Z21.88-2005 / CSA 2.33-2005

 Vented Gas 

Fireplace Heaters.

CAN/CGA-2.17-M91, 

Gas-Fired Appliances for 

Use at High Altitudes.

3.3 Installation Codes

This appliance must be installed in accordance with  
local codes if any or, in the absence of local codes, 
follow the 

National Fuel Gas Code, 

ANSI Z223.1 or 

Natural Gas and Propane Installation Code,

 CAN 

1-B149.

 3.4 High Altitude Installation 

When installing this appliance over 4,500 ft. (1,372 
m) above sea level in Canada, the appliance must 
be properly de-rated and installed according to local 
codes; in the absence of local codes, it must be 
installed in accordance with CAN/CGA-B149. In the 
US, for installations above 2,000 ft., the appliance 
must be installed in accordance with the current 
National Fuel Gas Code, ANSI Z223.1/ NFPA 54.

f i r e - p a r t s . c o m

Содержание 739DVN
































Отзывы: