background image

 

 

3

 

1.

 

SAFETY INFORMATION 

WARNING: Do not operate the appliance with the 
glass front removed, cracked or broken. Replacement 
of the glass should be done by a licensed or qualified 
service person. 
(The whole window unit may be temporarily removed 
by the owner for cleaning the interior of the firebox, 
etc.)  
Only the authorized Valor replacement window unit 
listed in the repair parts booklet must be fitted - never 
use substitutes. 
If the glass is damaged, search inside and adjacent to 
the appliance for any glass fragments. 
 
Due to high temperatures, the appliance should be 
located out of traffic and away from furniture and 
draperies. 
 
Children and adults should be alerted to the hazards 
of high surface temperatures and should stay away to 
avoid burns or clothing ignition. 
 
Young children should be carefully supervised when 
they are in the same room as the appliance. 
 
Clothing or other flammable material should not be 
placed on or near the appliance. 
 
This appliance must be installed and repaired by a 
qualified service person. The appliance should be 
inspected before use and at least annually by a 
professional service person. More frequent cleaning 
may be required due to excessive lint from carpeting, 
bedding material, etc. It is imperative that control 
compartments, burners and circulating air 
passageways of the appliance are kept clean. 
 

Keep curtains, clothing, furniture and other 
flammable materials a safe distance from all parts of 
the appliance and its vent system. 
 
Keep the appliance area well clear and free from 
combustible materials, gasoline and other flammable 
vapors and liquids. 
 
Never attempt to burn paper or any other material in 
the appliance. 
 
The venting terminal must not be recessed into a wall 
or siding. 
 
The vent terminal on the outside wall must be kept 
free from obstructions. No objects should be placed 
within 2 feet (60cm) of the vent terminal. The terminal 
is hot during operation and requires a guard if it is 
accessible to any person. An approved Valor guard is 
available from your dealer. 
 
During extreme weather conditions ensure that the 
vent outlet is free from ice and snow before attempting 
to light. 
 
Do not use this appliance if any part has been under 
water. Immediately call a qualified service technician 
to inspect the appliance and to replace any part of the 
control system and any gas control which has been 
under water. 

 

NOTE 

When operating your new fireplace for the first time, some vapors may be released due to the burning of curing compounds 
used in the manufacture of the appliance. They may cause a slight odor and could cause the flames to be the full height of the 
fire box, or even slightly higher, for the first few hours of operation. It is also possible that these vapors could set off any 
smoke detection alarms in the immediate vicinity. These vapors are quite normal on new appliances and are totally harmless 
but you may wish to open windows into the room to reduce the vapor/odor build up. After a few hours use the vapors will 
have disappeared and the flames will be at their normal height.   
During the first hour of use, the ceramic firebox walls may go a smoky color. This is not soot. It is a temporary effect lasting 
only while the ceramic material becomes stabilized. The walls will revert to their initial color after your fire has been used for 
one or two hours.     

Содержание 534AN






























Отзывы: