Valmet Flowrox FXM Series Скачать руководство пользователя

Страница: 32 / 46

4FXM70EN - 8/2022

4.2 Contact Input

Used to remotely start and stop pump using a close=stop

or open=stop signal. If pump should start on an open, then

select “Close: Stop Pump” option. Can be used with an

external foot pedal, a PLC, contact closure, or other similar

external devices.
Default settings: Disable
CC Input Range: 6 – 30 VDC OR

Dry Contact Closure (no voltage required)

Navigate to

Contact Input

menu by MENU button, then

selecting Input Setup, and then

Contact Input

Press UP or DOWN arrow to scroll through your options.
Press ENTER to make a selection. You should then notice

radio button (square box) is now filled in next to your

selection.
Press DOWN arrow to scroll down to OK selection. Then

press ENTER.
To navigate back out of menus, select ←Back and press the

ENTER button at bottom of every screen menu until you see

Run Mode screen displayed.

IMPORTANT:

If Contact Closure Input is enabled, pump

will display STANDBY if pump is in Stop mode via the

Contact Closure. Please use caution in this mode. Pump can

Start at anytime. If you must perform maintenance to the

pump, Press STOP button.

When Contact Input is enabled, the word Remote will be

displayed on lower left side of screen at all times

*NOTE: YOU MUST SET THE “CC1 OR CC2” FORMAT

UNDER THE CONDITIONAL LOGIC SECTION 4.5 TO

ENABLE INPUT CONTROL.

Signal stopped pump:

Signal started pump:

4.3 Remote/Local Control

The FXM can be configured for Remote control only, Local

control only, or either (disabled).
When set for Remote control only, all touch pad buttons

except the menu button are disabled. To completely lock

out the menu, configure a password (see page 19, Set

Password). If REMOTE ONLY is selected, the user is

prompted to select an input operating mode which must then

be used when operating the pump.
When set for LOCAL CONTROL only, all input signals

including the remote start/stop are disabled. Note that

the “Contact Closure Input” menu setting (section 4.3) is

switched to “disabled” while

LOCAL CONTROL ONLY

is selected. This menu setting will return to the previous

setting when

REMOTE CONTROL ONLY

or DISABLED is

selected.

Содержание Flowrox FXM Series















































Результаты поиска

Содержание Flowrox FXM Series

Отзывы:

Похожие инструкции для Flowrox FXM Series

Бренды по названию

Популярные бренды

Valmet Flowrox FXM Series, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Flowrox FXM Series

Отзывы:

Похожие инструкции для Flowrox FXM Series

Бренды по названию

Популярные бренды