- 18 -
TILTED/SLANTED COMBINED CUT (fig. G-H)
WarnInG! this cut requires the blade to be more exposed, increasing the risk of
serious injuries: take care of your hands and keep a safe distance.
Initial position:
- set the machine in “cutting off” mode
- the rotary table (pos. 9) is locked by the screw (pos. 11) at an angle between -45° and
+45° (in order to simplify the choice the table has catches at typical angles, however
it can be set at any angle)
- the cutting head is blocked by the lever (pos. 23) at an angle between 0° and 45°
Cutting:
- push the piece against the supporting guide (pos.10) and lock it into place with the
vice (pos.14) securely
WarnInG! Keep hands away from the cutting area.
- take hold of the hand grip (pos. 3) with your right hand, press the switch (pos.1) to
start the machine
- unlock the down stop by pressing the button (pos. 4)
- gradually lower the cutting head completely until the piece is cut
- slowly lift the cutting head and, as soon as the blade has left the piece, release the
switch to turn off the machine.
- follow the cutting head until it is in the resting position.
SAW BENCH MODE
OPERATOR
The normal operator position is in front of the machine, with both hands pushing the
piece towards the blade while exerting slight pressure on the surface. During the final
stage, the operator uses the piece pusher with one hand only (fig. L).
Warning! Keep your hands and face far from the blade and cutting area. Serious
injury hazard!
WORK SURFACE
The work surface (pos. 17) must be positioned correctly before starting any operation,
for this reason it can be moved upwards or downwards:
- to the highest position in cutting off mode
- to the lowest position in saw bench mode
It is forbidden to position the surface at an intermediate height.
Using the screw (pos. 22) and the lever (pos. 25) the movement of the work surface
can be locked or freed; whilst working the screw must be kept tightened well and the
lever must be turned upwards to lock the surface.
In order to facilitate movement, the work surface has a pair of springs, which push
it upwards into the correct position. However, check that it reaches the highest point
before switching over to cutting off mode.
Follow the indications reported in the “Operational procedures” chapter carefully
in order to move the surface correctly.
WORK PIECE
The shape, size and weight of the piece to be cut must be compatible with the machine.
Mark the cutting line on the piece with a ruler. Position it on the machine surface (pos.17),
taking care not to touch the blade, and rest it sideways against the piece guide (pos.19)
that you previously adjusted. The wider side of the piece must rest on the surface; do
not cut pieces with the wider side upright.
Warning! For your safety, it is important that the machine is secured to the bench
or stand.
Two pieces of defined dimensions (thickness H, see chap. Technical Data) can be
assembled on this machine. To support long pieces it is necessary to use a stand to be
arranged behind the machine, which prevents the 2 pieces from tipping over, causing
danger for the operator.
Align the line traced previously with the theoretical surface the piece shall create with
its straight motion through the blade.
WarnInG! For your safety, it is important that the piece is correctly locked. Do not
cut circular sections, old or fragile wood, irregular wood, cracked wood, wood with
nails or screws, branches or trunks. always carefully inspect the piece.
WarnInG! always remember that a kickback causes the rejection of the piece,
which is ejected towards the operator.
TOOL
Make sure the blade is integral, without cracks or deformations before use. Periodically
check blade sharpness.
When necessary, replace it following the instructions in the next chapters.
Warning! Blade efficiency and perfect integrity provide better results and minimize
accident risks.
CHIP AND DUST VACUUM
The machine can be equipped with a manifold (pos. 26) for the suction of sawdust.
Please remember that the part of material removed while cutting will also be thrown
around the machine and on the piece.
For a single cut it is sufficient to assemble the dust/chip bag (pos.30 if applicable),
which must be inserted at the bottom on the manifold as shown in fig.A; after cutting,
empty the bag.
In order to increase the number of cuts and, most of all, to obtain best results, connect
the manifold to a wood sawdust suction system, using a plastic flexible tube (both not
supplied with the machine); your dealer can suggest the most suitable choice.
Warning! Do not start the machine if the vacuum tube is not installed. Do not insert
your fingers or tools in the manifold in the attempt to remove material. Serious
injury hazard!
PUSH STICK
Before performing the cutting maintain the pusher at hand. If not used, store it away
from moving parts.
KNIFE DIVIDER
It is a comp onente important for safety and must be adjusted with respect the disc
blade (Fig. N). The thickness of the riving knife must be less than the width of the cut
groove and supeiore to the thickness of the metal disc of the blade.
OPERATIONS, CUTTING AND MOVEMENTS
The blade is fixed to the machine, while the piece moves manually in a straight and
parallel line in relation to the blade.
The motor provides power to rotate the tool, using a set of gears.
Observe the following warnings that apply to all types of cuts:
- make sure that levers and screws are tightened to firmly secure mobile parts
- keep the work piece firmly
- the piece must rest against the surface (pos.17) and the piece guide (pos.19)
- do not cut several pieces simultaneously
- keep a safety distance from the cutting area
- gradually and cautiously near the piece to the blade
- cut in a single stroke
- do not force the piece against the blade so as not to strain the blade and the engine
- excessive strains cause the blade and/or piece to suddenly break
- do not strain the blade laterally
- the idle blade should not touch the piece
- do not start the machine if the blade is in contact with the piece
- do not start the machine if the higher guard is not covering the blade (pos.15)
- do not start the machine if the removable guard is not positioned over the blade
(pos. 16) underneath the work surface
- to clean the cutting area, use a brush with a long handle
The machine can make various types of cuts:
- cut along the axis of the piece
- slanted cut
CUT ALONG THE AXIS OF THE PIECE (fig. L)
Initial position:
- set the machine in “saw bench” mode
- the rotary table (pos. 9) is locked at 0° with the screw (pos. 11)
- the cutting head is fixed at 0° by the lever (pos. 23)
- the piece guide (pos. 19) must be installed on the work surface as shown in fig. L.
Cutting:
- press the switch (pos. 2) to start the machine
- using both hands, push the piece against the blade (enclosed in the guard) at a uniform
speed and, at the same time, press the piece onto the work surface and on the piece
guide. The part will cause the upper guard to lift (pos. 15) and to rest onto the piece
keeping the blade protected
WarnInG! Keep hands away from the cutting area.
- when your hands get closer to the blade, use the piece pusher to complete the cut
- once you have finished cutting, switch off the machine.
SLANTED CUT
WarnInG! Carrying out this cut means that the hands are located in the area
adjacent to the cut and the danger of serious injury is therefore greater: take care
of your hands and keep a safe distance.
WarnInG! It is forbidden to carry out this type of cut on long pieces, such as planks,
beams, etc. Only use pieces of a limited length.
Initial position:
- set the machine in “saw bench” mode
- the rotary table (pos. 9) is locked at 0° with the screw (pos. 11)
- the cutting head is fixed at 0° by the lever (pos. 23)
- piece guide (pos.19) installed on the work surface parallel to the blade and adjusted
at an angle
Cutting:
- press the switch (pos. 2) to start the machine
- grasp the piece and the piece guide with both hands and push them forwards, making
the piece guide slide along the slot and at the same time, press the piece onto the work
surface. The piece will cause the upper guard to be lifted (pos.15) that will then rest
on the piece, keeping the blade protected.
WarnInG! Keep hands and the piece guide far from the cutting area.
- finish cutting
- turn off the machine.
BLaDe
WarnInG! the cutting part can cause serious injuries – use protection gloves!
- Use good quality blades with the same characteristics as the machine based on its
technical data – your retailer will be able to help you make the correct choice. Also
observe any instructions provided with the equipment.
- Do not use blades if you do not know where they are from or without technical speci-
fications. They must show the nominal dimensions, the number of teeth, the maximum
number of revolutions and the arrow indicating the rotation direction.
- The number of revolutions and the dimensions are the basic elements for making your
choice. The number of revolutions must always be higher or equal to that shown on the
machine. The dimensions must be equal to those shown on the machine.
- Use blades which conform to the regulations in force in the country of use.
- Do not use HSS (high speed steel) blades or abrasive truncating discs.
- Always carry out a simple visual check: there must be no deformations, breakages
or damages.
Our company provides a complete series of blades suitable for your machine, which
you can buy from your retailer.