Vaillant VRT 360f Operating and Скачать руководство пользователя

Страница: 43 / 48

Installation instructions

VRT 360f

Restoring the default settings

• To return the room temperature

thermostat to its default settings,
press the P button for 15 seconds. As
soon as the display lights up twice, the
room temperature thermostat has
been reset. This means that you will
have to perform all individual settings
again.

11.3

Handing over the appliance to
the owner

The owner of the room temperature
thermostat must be instructed about its
functions and how to operate it.
• Hand over the manuals intended for

the owner as well as the documents of
the appliance.

• Go through the operating manual with

him and answer his questions.

• Draw special attention to the safety

instructions which the owner must
follow.

• Tell the owner to keep the manuals

nearby the controller.

Start-up 11

Содержание VRT 360f Operating and

















































Результаты поиска

Содержание VRT 360f Operating and

Отзывы:

Похожие инструкции для VRT 360f Operating and

Бренды по названию

Популярные бренды

Vaillant VRT 360f Operating and, Руководство по эксплуатации и установке

Результаты поиска

Содержание VRT 360f Operating and

Отзывы:

Похожие инструкции для VRT 360f Operating and

Бренды по названию

Популярные бренды