Vaillant ecoCOMPACT VCC4 Series Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 68

background image

Appendix

48

Installation and maintenance instructions ecoCOMPACT 0020181421_04

Code Parameter

Values or explanations

Default
setting

User-spe-
cific setting

D.074 Anti-legionella function

0 = Off
1 = On
Thermal disinfection is carried out every 24 hours

0 = Off

D.075 Maximum charging time for the

domestic hot water cylinder

20 - 90 min

45 mins

D.076 Device specific number

Unit variant display (DSN)

Not ad-
justable

D.077 Limit on cylinder charging output in

kW

Adjustable cylinder charging output in kW

D.078 Max. flow temperature during post-

heating of the cylinder

Adjustable cylinder charging output in kW
50 … 80

℃

75

℃

D.080 Operating hours of the burner in

heating mode

In hours (h)

Not ad-
justable

D.081 Operating hours of the burner for

domestic hot water generation

In hours (h)

Not ad-
justable

D.082 Number of burner start-ups in heat-

ing mode

Number of burner start-ups

Not ad-
justable

D.083 Number of burner starts in domestic

hot water mode

Number of burner start-ups

Not ad-
justable

D.085 Minimum unit output

In kW

Not ad-
justable

D.090 Status of the digital eBUS control

Recognised, not recognised

Not ad-
justable

D.091 Status of DCF with outdoor temper-

ature sensor connected

No reception
Reception
Synchronised
Valid

Not ad-
justable

D.093 Unit variant setting (DSN)

Adjustment range: 100 to 199
The three-digit DSN code is located on the product's
data plate.

D.094 Delete fault history

Delete fault list
0 = No
1 = Yes

D.095 Software version of PeBUS compon-

ents

PCB (BMU)
Display (AI)
Solar card (SMU)

Not ad-
justable

D.096 Default setting

Reset all adjustable parameters to factory setting
0 = No
1 = Yes

D.098 Value of coding resistors for gas

group and output range

Display xx.yy
xx = Coding resistor 1 in cable harness for output range:
08 = Up to 25 kW
09 = up to 30 kW
10 = up to 34 kW
yy = Coding resistor 2 on PCB for gas type (read gas
category of the unit):
02 = P gas or G31
03 = E gas or G20
07 = L gas or G25

Not ad-
justable

D.121 Enriching the air/gas mixture at min.

output

0 = Normal
1 = Enriched
2 = Slightly enriched

0 = Normal

D.122 Limited available pressure

In mbar, for proKlima only

D.123 Time cylinder was last charged

min

Not ad-
justable

D.124 Domestic hot water cylinder in ECO

mode

0 = Function deactivated
1 = ECO mode activated

0 = Function
deactivated

Not ad-
justable

D.125 Domestic hot water temperature at

the cylinder outlet

Actual value in °C

Not ad-
justable

«
...
46
47
48
49
50
...
»

Содержание ecoCOMPACT VCC4 Series





































































Отзывы:

Нет отзывов

Похожие инструкции для ecoCOMPACT VCC4 Series

Бренд: Vaillant Страницы: 56

MultiTemp MR Series

Бренд: HydroTherm Страницы: 36

Бренд: Glow-worm Страницы: 12

Бренд: Reliable Страницы: 1

Ultra Ultra Series 1

Бренд: Weil-McLain Страницы: 2

Бренд: Weil-McLain Страницы: 4

Бренд: Weil-McLain Страницы: 36

Gold GV 1 series

Бренд: Weil-McLain Страницы: 1

Бренд: Weil-McLain Страницы: 12

Бренд: Weil-McLain Страницы: 12

Бренд: Weil-McLain Страницы: 44

Бренд: Weil-McLain Страницы: 44

Бренд: Palazzetti Страницы: 148

Mexico Super RS4100

Бренд: Ideal Boilers Страницы: 36

Бренд: baxiroca Страницы: 44

COMBIflo 100/300

Бренд: andrews Страницы: 76

ECOMAXI 160 ErP

Бренд: Sime Страницы: 148

29CDi GC 47-406-34

Бренд: Worcester Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды