Vaillant ecoCOMPACT VCC4 Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 68

background image

Start-up 7

0020181421_04 ecoCOMPACT Installation and maintenance instructions

19

7.2

Checking the factory setting

Applicability:

Except Belgium

Caution.
Risk of material damage caused by mak-
ing unauthorised settings.

▶

Never modify the factory setting of the gas
pressure regulator of the gas valve.

Note

Each destroyed seal must be restored.

1

Note

Some units are equipped with gas valves that
have no pressure regulator

(1)

.

Caution.
An incorrect gas group setting may cause
operating faults or a reduction in the ser-
vice life of the product.

If the product design does not match the local
gas group, malfunctions will occur or you will
have to replace product components prema-
turely.

▶

Before you start up the product, compare
the gas group information on the data
plate with the gas group available at the
installation site.

The product's combustion has been factory tested and is
preset for operation with the gas group indicated on the iden-
tification plate.

Conditions

: The product design

is not compatible

with the local gas

group

▶

Do not start up the product.

▶

Change the type of gas in accordance with your system.

Conditions

: The product design

is compatible

with the local gas group

▶

Proceed as described below.

7.3

Filling the condensate siphon

Danger!
Risk of poisoning due to escaping flue
gas.

An empty or insufficiently filled condensate
siphon may allow flue gas to escape into the
room air.

▶

Fill the condensate siphon with water be-
fore starting up the product.

1

1.

Remove the lower section of the siphon

(1)

by turning

the bayonet fitting anti-clockwise.

2.

Fill the lower section of the siphon with water up to 10
mm below the upper edge.

3.

Screw the lower section back onto the condensate si-
phon correctly.

7.4

Switching on the product

▶

Press the on/off button on the product.

◁

The basic display appears on the display.

7.5

Running the installation assistants

The installation assistant is displayed whenever the product
is switched on until it has been successfully completed.
It provides direct access to the most important check
programmes and configuration settings for starting up the
product.

Confirm the launch of the installation assistant. All heating
and domestic hot water demands are blocked whilst the in-
stallation assistant is active.

Confirm that you want to navigate to the next point by press-
ing

Next

.

If you do not confirm the launch of the installation assistant,
it is closed 10 seconds after you switch on the unit and the
basic display then appears.

«
...
17
18
19
20
21
...
»

Содержание ecoCOMPACT VCC4 Series





































































Отзывы:

Нет отзывов

Похожие инструкции для ecoCOMPACT VCC4 Series

Бренд: Glow-worm Страницы: 44

Бренд: Hounsfield Boilers Страницы: 8

Бренд: Alpha Страницы: 4

Бренд: Ideal Boilers Страницы: 8

Бренд: Crown Boiler Страницы: 23

Бренд: Olsen Страницы: 84

MEGAPREX N 1060N

Бренд: Lamborghini Caloreclima Страницы: 108

Бренд: IDEAL Страницы: 8

Бренд: Optima Страницы: 8

Vitocrossal 300 CR3

Бренд: Viessmann Страницы: 48

Бренд: NTI Страницы: 72

Бренд: Saunier Duval Страницы: 4

Бренд: Buderus Страницы: 64

Logano plus GB402

Бренд: Buderus Страницы: 76

Бренд: Ferroli Страницы: 88

Бренд: Clifton Range Страницы: 10

Бренд: STI Страницы: 10

Бренд: Rinnai Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды