Vaillant ecoCOMPACT VCC4 Series Скачать руководство пользователя страница 26

Страница: 26 / 68

7 Start-up

Installation and maintenance instructions ecoCOMPACT 0020181421_04

▶

Pierce the covering cap

(1)

at the mark using a small

flat-blade screwdriver and unscrew it.

▶

Set the CO

₂

content (value with front casing removed)

by turning the screw

(2)

Note

Turn to the left: Higher CO

₂

content

Turn to the right: Lower CO

₂

content

▶

For natural gas only: Adjust the value in increments of
1 turn and wait approx. 1 minute after each adjustment
until the value stabilises.

▶

For liquid gas only: Adjust the value in small increments
of 1/2 turn and wait approx. 1 minute after each adjust-
ment until the value stabilises.

▶

Once the setting is finished, lock the check programme.

▶

If an adjustment is not possible in the specified adjust-
ment range, you must not start up the product.

▶

If this is the case, inform Vaillant Customer Service.

▶

Screw the covering cap back in.

▶

Refit the front casing.

7.15.3 Checking the CO

₂

content and, if necessary,

adjusting it (air ratio setting)

Applicability:

Belgium

Start up the product with the check programme

P.01

Wait at least five minutes until the product reaches its
operating temperature.

Measure the CO

₂

content at the flue gas analysis point

(1)

If the measured values are not in the specified range,
you must not start up the product.

If this is the case, inform Vaillant Customer Service.

Compare the measured value with the corresponding
value in the table.
Gas adjustment values as set at the factory (

→

Page 55)

7.16

Checking leak-tightness

▶

Check the gas pipe, the heating circuit and the hot water
circuit for leak-tightness.

▶

Check that the air/flue pipe has been installed correctly.

Conditions

: Room-sealed operation

▶

Check whether the vacuum chamber has been closed
tightly.

7.16.1 Checking the heating mode

Make sure that there is a heat requirement.

–

E.g. using settings on the system control or cooling
the buffer cylinder.

Note

Alternatively, you can use the service soft-
ware to make a target flow value specifica-
tion.

Call up the

Live Monitor

–

Menu

→

Live Monitor

◁

If the product is working correctly, the display shows

S.04

7.16.2 Checking the hot water generation

Open a hot water valve all the way.

Call up the

Live Monitor

Содержание ecoCOMPACT VCC4 Series





































































Результаты поиска

Содержание ecoCOMPACT VCC4 Series

Отзывы:

Похожие инструкции для ecoCOMPACT VCC4 Series

Бренды по названию

Популярные бренды

Vaillant ecoCOMPACT VCC4 Series, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ecoCOMPACT VCC4 Series

Отзывы:

Похожие инструкции для ecoCOMPACT VCC4 Series

Бренды по названию

Популярные бренды