Vaderstad E-services Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 48

background image

12

Alarm list

21. Seed feed rotation LH

If the metering units do not move:

Check that the toothed coupling between the hydraulic motor and the feed
shaft is in the correct position and intact.

If the alarm appears although the
seed meters:

Check the alert time that has been programmed.

Check the sensor. The sensor is
located in the tramline coupling:

Check connections and connectors to the tramline coupling.

The sensor in the coupling could be defective.

The coupling could be defective. Check that the roller in the coupling is
rotating with the feed shaft. The roller should rotate when tramlining is off.

22. Seed feed rotation RH

If the metering units do not move:

Check that the toothed coupling between the hydraulic motor and the feed
shaft is in the correct position and intact.

If the alarm appears although the
seed meters:

Check the alert time that has been programmed.

23. Seed feed rotation LH and RH

If the metering units do not move:

Check that the toothed coupling between the hydraulic motor and the feed
shaft is in the correct position and intact.

If the alarm appears although the
seed meters:

Check the alert time that has been programmed.

Check the sensor. The sensor is
located in the tramline coupling:

Check connections and connectors to the tramline coupling.

The sensor in the coupling could be defective.

The coupling could be defective. Check that the roller in the coupling is
rotating with the feed shaft. The roller should rotate when tramlining is off.

31. Seed feed BioDrill Rotation LH

If BioDrill is not in use:

Turn off the alarm function. Go to the programming menu on the control unit
and switch off BioDrill.

If the metering units do not move:

Check that the toothed coupling between the hydraulic motor and the feed
shaft is in the correct position and intact.

If the alarm appears although the
seed meters:

Check the alert time that has been programmed.

Check the cables, contacts and connection.

Check the operation of the sensor. The sensor LED should light when the
toothed plate passes. The distance between the sensor and the pulse disc must
be 1–2 mm. Adjust if necessary. An illuminated diode is no guarantee that the
sensor is working properly.

Check the condition and installation of the toothed plate.

32. Seed feed, BioDrill rotation RH

If BioDrill is not in use:

See alarm no. 31

32

903099-en-gb; 19.01.2021

«
...
34
35
36
37
38
...
»

Содержание E-services

















































Отзывы:

Нет отзывов

Похожие инструкции для E-services

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

BELMONT 2001039

Бренд: Backyard Discovery Страницы: 50

Бренд: Backyard Discovery Страницы: 45

Бренд: Backyard Discovery Страницы: 70

Бренд: BACtrack Страницы: 16

Бренд: PANDROL Страницы: 36

Бренд: Badger Basket Страницы: 7

Бренд: Backyard Discovery Страницы: 53

Бренд: Rainbow Страницы: 18

Бренд: Major Страницы: 52

BOMAG BW 100 ADM-5

Бренд: Fayat Страницы: 216

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды