Vacon OPTA1 Скачать руководство пользователя страница 22

Страница: 22 / 23

22 • vacon

Fault codes

Tel.+358 (0)201 2121 • Fax +358 (0)201 212 205

Unbalance
(Warning only)

Unbalance between power modules in
paralleled units.
Subcode in T.14:
S1 = Current unbalance
S2 = DC-Voltage unbalance

Should the fault re-occur, contact your
local distributor.

IGBT
temperature
(hardware)

IGBT Inverter Bridge overtemperature
protection has detected too high short
term overload current

Application

Problem in application software

Contact your distributor. If you are
application programmer check the
application program.

Device changed
(same type)

Option board or power unit changed.
New device of same type and rating.

Reset. Device is ready for use.
Old parameter settings will be used.

Device added
(same type)

Option board added.

Reset. Device is ready for use.
Old board settings will be used.

Device removed Option board removed.

Reset. Device no longer available.

Device
unknown

Unknown option board or drive.
Subcode in T.14:
S1 = Unknown device
S2 = Power1 not same type as Power2

Contact the distributor near to you.
Please visit:

http://www.vacon.com/wwcontacts.html

IGBT temperature IGBT Inverter Bridge overtemperature

protection has detected too high a short
term overload current

Device changed
(different type)

Option board or power unit changed.
New device of different type or different
rating than the previous one.

Reset
Set the option board parameters again if
option bard changed. Set converter
parameters again if power unit changed.

Device added
(different type)

Option board of different type added.

Reset
Set the option board parameters again.

External fault

Digital input fault.

- Remove fault situation from external
device.

Slot fault

Defective option board or slot

Check board and slot.
Contact the nearest Vacon distributor.
Please visit:

http://www.vacon.com/wwcontacts.html

PT100 fault

Temperature limit values set for the
PT100 have been exceeded.

KLIXON

Status of KLIXON input is LOW.

Thermistor
fault

The thermistor input of option board has
detected too high resistor temperature

Check resistors.
Check thermistor connection
(If thermistor input of the option board is
not in use it has to be short circuited)

Table 6-1. Fault codes

Содержание OPTA1
























Результаты поиска

Содержание OPTA1

Отзывы:

Похожие инструкции для OPTA1

Бренды по названию

Популярные бренды

Vacon OPTA1, Руководство пользователя

Результаты поиска

Содержание OPTA1

Отзывы:

Похожие инструкции для OPTA1

Бренды по названию

Популярные бренды